Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B228562  Steering Lock Position Signal Compare Failure  


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator with ECU assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B228562 Steering Lock Position Signal Compare Failure The steering lock position signal sent by the steering lock ECU (steering lock actuator with ECU assembly) via direct line and the steering lock position signal sent via LIN communication do not match. (1-trip detection logic*)
·

LIN communication system

·

Steering lock ECU (steering lock actuator with ECU assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control B
DTC Output Confirmation Operation:

Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) battery terminal. Wait at least 40 seconds with the ignition switch off (steering locked), then turn the ignition switch to ON (steering unlocked) and wait at least 40 seconds.



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine cannot be started. The ECU does not send an engine start request.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B228562
Power Source Control

Steering Unlock Switch


Entry&Start
·

Power Supply Short History

·

Motor Driver Short History

·

Lock Bar Stuck Error History



WIRING DIAGRAM

E417559E20
0.313,3.302 2.448,3.688 2.135,0.385 10 false Steering Lock ECU (Steering Lock Actuator with ECU Assembly) 0.5,2.698 1.521,3.083 1.021,0.385 10 false Unlock Sensor 1.406,1.271 1.729,1.479 0.323,0.208 10 false +B 1.948,1.76 2.344,1.969 0.396,0.208 10 false SLP 2.365,1.76 2.688,1.969 0.323,0.208 10 false 4 4.99,1.771 5.313,1.979 0.323,0.208 10 false 11 5.094,3.271 6.625,3.958 1.531,0.688 10 false Certification ECU (Smart Key ECU Assembly) 5.094,3.104 5.479,3.354 0.385,0.25 10 false I39 5.271,1.771 5.594,1.979 0.323,0.208 10 false SLP 5.573,1.146 5.896,1.354 0.323,0.208 10 false +B 6.073,1.771 6.396,1.979 0.323,0.208 10 false IC 0.906,4.333 3.083,4.667 2.177,0.333 10 false : LIN Communication Line 0.302,3.125 0.688,3.375 0.385,0.25 10 false I49

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator with ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
HINT:
·

If the steering cannot be unlocked, the ignition switch cannot be turned to ON and the engine cannot be started.

·

If LIN communication is not available, the steering cannot be locked or unlocked.



Result:
Result Proceed to
B278588 is not output A
B278588 is output B




A

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)

B

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock ECU (steering lock actuator with ECU assembly) OFF or ON OFF: Steering locked
·

When the shift lever is in P and the ignition switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned ACC or ON, the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 454 204
OK:

The GTS display changes.


Result:
Result Proceed to
The value of Steering Unlock Switch is OFF A
The value of Steering Unlock Switch is not OFF B




A

3.READ VALUE USING GTS (STEERING UNLOCK SWITCH)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

3.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock ECU (steering lock actuator with ECU assembly) OFF or ON ON: Steering unlocked
·

When the shift lever is in P and the ignition switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned ACC or ON, the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 454 204
OK:

The GTS display changes.


Result:
Result Proceed to
The value of Steering Unlock Switch is ON A
The value of Steering Unlock Switch is not ON B




A

4.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

4.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.
C342153C79
1.521,0.177 1.938,0.427 0.417,0.25 1.104,1.74 1.24,1.74 1.24,1.74 1.708,1.125 true 0.188,0.177 0.5,0.375 0.313,0.198 10 false *a 0.781,1.656 1.219,1.865 0.438,0.208 10 false SLP 1.625,0.219 1.938,0.417 0.313,0.198 10 false I49
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-4 (SLP) - Body ground*1 Steering locked 10 kΩ or higher
I49-4 (SLP) - Body ground*1 Steering unlocked*2 Below 1 Ω


HINT:
·

*1: Tester connection: Positive (+) tester probe → I49-4 (SLP), Negative (-) tester probe → Body ground

·

*2: If any of the doors are opened with the shift lever in P and the ignition switch off, the steering will be locked. If the ignition switch is turned to ACC or ON with the electrical key transmitter sub-assembly in the cabin, the steering will be unlocked.

·

DTC B228562 may be stored due to a malfunction in the steering lock ECU (steering lock actuator with ECU assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator with ECU assembly) to the certification ECU (smart key ECU assembly) individually.



Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY))

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


Procedure1


Post-procedure1

d.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR