Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2022.11
RM38G0E _51 Engine / Hybrid System _101047 STOP AND START _0469044 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the audio and visual system from malfunctioning if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control.

If any DTCs are output, troubleshoot the DTCs first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:
·

Tire pressure warning system

·

Toyota multi operation touch system

·

Headup display system

·

Pre-Collision System

·

Air conditioning system

·

Parking support brake system

·

Lane tracing assist system

·

Vehicle stability control system

·

Meter / gauge System

·

Navigation system

·

Lighting system



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator Symptom Proceed to
When the engine is restarted by stop and start control:
The following symptoms may occur
·

Audio and visual system is reset

·

The combination meter assembly fades out


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

Duty error

·

Communication cycle error


Stop and start control prohibited P323A00
P323AA2
P323B29
P323B38
Blinks Converter output voltage cannot be boosted when the engine is restarted A
Battery voltage drop
Systems on the converter output side do not operate
B41 terminal: Both of the following will not operate
·

Tire pressure warning system

·

Vehicle stability control system


B42 terminal: The navigation system will not operate
B43 terminal: Both of the following will not operate
·

Navigation system

·

Headup display system

·

Air conditioning system

·

Toyota multi operation touch system

·

Lighting system


IG41 terminal: All of the following will not operate
·

Tire pressure warning system

·

Toyota multi operation touch system

·

Headup display system

·

Air conditioning system

·

Parking support brake system

·

Pre-Collision System


Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
P323A19 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IGP terminal: All of the following will not operate
·

Tire pressure warning system

·

Toyota multi operation touch system

·

Headup display system

·

Air conditioning system

·

Parking support brake system

·

Lane tracing assist system

·

Vehicle stability control system

·

Meter / gauge system

·

Pre-Collision System


IGR terminal: -
ACC terminal: All of the following will not operate
·

Navigation system

·

Toyota multi operation touch system

·

Air conditioning system


Converter input circuit malfunction
·

Open or short to GND in IGR circuit

·

Open or short to GND in IGP circuit

·

Open or short to GND in ACC circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate (varies depending on the malfunctioning relay circuit the converter detected)
AC42 terminal: All of the following will not operate
·

Navigation system

·

Toyota multi operation touch system

·

Air conditioning system


IG12 terminal: The meter / gauge system will not operate
IG31 terminal: All of the following will not operate
·

Lane tracing assist system

·

Vehicle stability control system


IG41 terminal: All of the following will not operate
·

Tire pressure warning system

·

Toyota multi operation touch system

·

Headup display system

·

Air conditioning system

·

Parking support brake system

·

Pre-Collision System


B41 terminal: Both of the following will not operate
·

Tire pressure warning system

·

Vehicle stability control system


B42 terminal: The navigation system will not operate
B43 terminal: Both of the following will not operate
·

Navigation system

·

Headup display system

·

Air conditioning system

·

Toyota multi operation touch system

·

Lighting system


Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following systems do not operate
·

Tire Pressure Warning System

·

Toyota Multi Operation Touch System

·

Headup Display System

·

Air Conditioning System

·

Parking Support Brake System

·

Lane tracing assist system

·

Vehicle Stability Control System

·

Meter / Gauge System

·

Navigation System

·

Lighting System

·

Pre-Collision System


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction


Stop and start control prohibited P061519 Does not blink (Due to disabled meter / gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P30DF62
P30EF4B
P323A00
P323A16
P323AA2
P323B29
P323B38
The audio does not operate (until the ignition switch is turned off) Excessive audio volume Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected The relay circuit in the converter is turned off to cut off power supply to the audio and visual system (navigation system) (Returns to normal when the ignition switch is turned off) - Does not blink If overcurrent is detected in the audio and visual system (navigation system), system operation is disabled while the ignition switch is ON (Returns to normal when the ignition switch is turned off) C
The external backup boost converter (eco run vehicle converter assembly) output side system does not operate
·

Navigation system

·

Audio and visual system

·

Active noise control system


·

Open in PA-BBC fuse circuit

·

Malfunction in circuits the converter supplies power to

·

External backup boost converter (eco run vehicle converter assembly) malfunction


- - Does not blink All systems that the converter supplies power to do not operate (see circuit diagram) D
·

The combination meter assembly cannot be turned off (short between IG12 and +B)

·

Communication error DTCs may be stored due to short between AC42 and +B


HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between IG12 and +B

·

Short between AC42 and +B


- - Does not blink The converter cannot shut off the power source when the ignition switch is turned off B
·

Ignition switch cannot be turned off from ACC (short between ACC and +B)

·

Ignition switch cannot be turned off from ON (short between IG1 or IG2 and +B)


Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IG1 and +B

·

Short between IG2 and +B


- - Does not blink
·

Ignition switch does not turn ACC

·

Ignition switch cannot be turned off


B


Result:
Proceed to
A
B
C
D



A

GO TO DIAGNOSTIC TROUBLE CODE CHART

B

2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)

C

5.CHECK AUDIO AND VISUAL SYSTEM

D

7.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)
a.

Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B37)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-1 (BIN2) - Body ground Always 9.5 to 14 V
B37-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V
I57-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V



g.

Turn the ignition switch off.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-21 (IGR) - Body ground Ignition switch off 0 to 1 V
I57-19 (ACC) - Body ground Ignition switch off 0 to 1 V
I57-18 (IGP) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tire Pressure Warning System
Tester Connection Condition Specified Condition

Click Location & Routing(I57,T21)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(T21)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assembly

I57-3 (IG41) - T21-1 (IG) Always Below 1 Ω
I57-2 (B41) - T21-7 (+B) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
T21-1 (IG) - Body ground Always 10 kΩ or higher
I57-2 (B41) - Body ground Always 10 kΩ or higher
T21-7 (+B) - Body ground Always 10 kΩ or higher

Integration Control Sub-assembly*1
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I22)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

I57-3 (IG41) - I22-4 (IG+) Always Below 1 Ω
I57-26 (AC42) - I22-3 (ACC) Always Below 1 Ω
I57-11 (B43) - I22-1 (B) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
I22-4 (IG+) - Body ground Always 10 kΩ or higher
I57-26 (AC42) - Body ground Always 10 kΩ or higher
I22-3 (ACC) - Body ground Always 10 kΩ or higher
I57-11 (B43) - Body ground Always 10 kΩ or higher
I22-1 (B) - Body ground Always 10 kΩ or higher

Meter Mirror Sub-assembly*2
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I17)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I57-3 (IG41) - I17-1 (IG) Always Below 1 Ω
I57-11 (B43) - I17-2 (B) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
I17-1 (IG) - Body ground Always 10 kΩ or higher
I57-11 (B43) - Body ground Always 10 kΩ or higher
I17-2 (B) - Body ground Always 10 kΩ or higher

No. 2 Air Conditioning Control Assembly*3
Tester Connection Condition Specified Condition

Click Location & Routing(I57,Q52)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

I57-3 (IG41) - Q52-10 (IG) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
Q52-10 (IG) - Body ground Always 10 kΩ or higher

Clearance Warning ECU Assembly
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I58)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

I57-3 (IG41) - I58-1 (IG) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
I58-1 (IG) - Body ground Always 10 kΩ or higher

Air Conditioning Control Assembly
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I78)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

I57-3 (IG41) - I78-8 (IG+) Always Below 1 Ω
I57-26 (AC42) - I78-7 (ACC) Always Below 1 Ω
I57-11 (B43) - I78-16 (+B) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
I78-8 (IG+) - Body ground Always 10 kΩ or higher
I57-26 (AC42) - Body ground Always 10 kΩ or higher
I78-7 (ACC) - Body ground Always 10 kΩ or higher
I57-11 (B43) - Body ground Always 10 kΩ or higher
I78-16 (+B) - Body ground Always 10 kΩ or higher

Millimeter Wave Rader Sensor Assembly*4
Tester Connection Condition Specified Condition

Click Location & Routing(I57,A10)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assembly

I57-3 (IG41) - A10-8 (IGB) Always Below 1 Ω
I57-3 (IG41) - Body ground Always 10 kΩ or higher
A10-8 (IGB) - Body ground Always 10 kΩ or higher

Power Steering ECU with Motor Assembly*5
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I71)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I71)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I57-23 (IG31) - I71-1 (IG) Always Below 1 Ω
I57-23 (IG31) - Body ground Always 10 kΩ or higher
I71-1 (IG) - Body ground Always 10 kΩ or higher

No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly)
Tester Connection Condition Specified Condition

Click Location & Routing(I57,B19)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

I57-23 (IG31) - B19-31 (IG1) Always Below 1 Ω
I57-2 (B41) - B19-14 (+BI1) Always Below 1 Ω
I57-23 (IG31) - Body ground Always 10 kΩ or higher
B19-31 (IG+) - Body ground Always 10 kΩ or higher
I57-2 (B41) - Body ground Always 10 kΩ or higher
B19-14 (+BI1) - Body ground Always 10 kΩ or higher

No. 2 Skid Control ECU (brake actuator assembly)
Tester Connection Condition Specified Condition

Click Location & Routing(I57,B20)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

I57-23 (IG31) - B20-45 (IG1) Always Below 1 Ω
I57-23 (IG31) - Body ground Always 10 kΩ or higher
B20-45 (IG1) - Body ground Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I5)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I57-10 (IG12) - I5-6 (IG+) Always Below 1 Ω
I57-10 (IG12) - Body ground Always 10 kΩ or higher
I5-6 (IG+) - Body ground Always 10 kΩ or higher

Radio Receiver Assembly*6
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I8)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I8)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I57-26 (AC42) - I8-3 (ACC1) Always Below 1 Ω
I57-12 (B42) - I8-4 (+B1) Always Below 1 Ω
I57-26 (AC42) - Body ground Always 10 kΩ or higher
I8-3 (ACC1) - Body ground Always 10 kΩ or higher
I57-12 (B42) - Body ground Always 10 kΩ or higher
I8-4 (+B1) - Body ground Always 10 kΩ or higher

Radio Receiver Assembly*7
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I10)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I57-26 (AC42) - I10-15 (ACC1) Always Below 1 Ω
I57-12 (B42) - I10-4 (+B1) Always Below 1 Ω
I57-26 (AC42) - Body ground Always 10 kΩ or higher
I10-15 (ACC1) - Body ground Always 10 kΩ or higher
I57-12 (B42) - Body ground Always 10 kΩ or higher
I10-4 (+B1) - Body ground Always 10 kΩ or higher

Multi-display Assembly*1
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I18)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

I57-26 (AC42) - I18-24 (ACC) Always Below 1 Ω
I57-11 (B43) - I18-12 (B) Always Below 1 Ω
I57-26 (AC42) - Body ground Always 10 kΩ or higher
I18-24 (ACC) - Body ground Always 10 kΩ or higher
I57-11 (B43) - Body ground Always 10 kΩ or higher
I18-12 (B) - Body ground Always 10 kΩ or higher

Navigation ECU
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I21)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

I57-11 (B43) - I21-10 (+B) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
I21-10 (+B) - Body ground Always 10 kΩ or higher

No. 1 Interior Illumination Light Assembly (for Front Passenger Side)
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I61)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I61)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Foot Light RH (No. 1 Interior Illumination Light Assembly)

I57-11 (B43) - I61-2 (B) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
I61-2 (B) - Body ground Always 10 kΩ or higher

No. 1 Interior Illumination Light Assembly (for Driver Side)
Tester Connection Condition Specified Condition

Click Location & Routing(I57,I62)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(I62)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Foot Light LH (No. 1 Interior Illumination Light Assembly)

I57-11 (B43) - I62-2 (B) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
I62-2 (B) - Body ground Always 10 kΩ or higher

No. 1 Interior Illumination Light Assembly LH
Tester Connection Condition Specified Condition

Click Location & Routing(I57,i6)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(i6)Seat>Front Seat Wire LH>Foot Light LH (No. 1 Interior Illumination Light Assembly LH)

I57-11 (B43) - i6-2 Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
i6-2 - Body ground Always 10 kΩ or higher

No. 1 Interior Illumination Light Assembly RH
Tester Connection Condition Specified Condition

Click Location & Routing(I57,h11)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(h11)Seat>Front Seat Wire RH>Foot Light RH (No. 1 Interior Illumination Light Assembly RH)

I57-11 (B43) - h11-2 Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
h11-2 - Body ground Always 10 kΩ or higher

Rear Door Inside Handle Illumination Light Switch LH
Tester Connection Condition Specified Condition

Click Location & Routing(I57,P5)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(P5)Body>No. 2 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly LH

I57-11 (B43) - P5-2 (+) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
P5-2 (+) - Body ground Always 10 kΩ or higher

Rear Door Inside Handle Illumination Light Switch RH
Tester Connection Condition Specified Condition

Click Location & Routing(I57,O5)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(O5)Body>No. 1 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly RH

I57-11 (B43) - O5-2 (+) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
O5-2 (+) - Body ground Always 10 kΩ or higher

Front Door Inside Handle Illumination Light Switch LH
Tester Connection Condition Specified Condition

Click Location & Routing(I57,N8)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LH

I57-11 (B43) - N8-2 (+) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
N8-2 (+) - Body ground Always 10 kΩ or higher

Front Door Inside Handle Illumination Light Switch RH
Tester Connection Condition Specified Condition

Click Location & Routing(I57,M10)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(M10)Body>Front Door Wire RH>Front Door Inside Handle Illumination Light Assembly RH

I57-11 (B43) - M10-2 (+) Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
M10-2 (+) - Body ground Always 10 kΩ or higher

Vanity Light Assembly (for LH side)
Tester Connection Condition Specified Condition

Click Location & Routing(I57,d5,d9)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LH

Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LH

I57-11 (B43) - d5-1 (B)*8 Always Below 1 Ω
I57-11 (B43) - d9-2 (B)*9 Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
d5-1 (B)*8 - Body ground Always 10 kΩ or higher
d9-2 (B)*9 - Body ground Always 10 kΩ or higher

Vanity Light Assembly (for RH side)
Tester Connection Condition Specified Condition

Click Location & Routing(I57,d4,d8)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

Click Connector(d4)Body>No. 1 Roof Wire>Vanity Light Assembly RH

Click Connector(d8)Body>No. 1 Roof Wire>Vanity Light Assembly RH

I57-11 (B43) - d4-1 (B)*8 Always Below 1 Ω
I57-11 (B43) - d8-2 (B)*9 Always Below 1 Ω
I57-11 (B43) - Body ground Always 10 kΩ or higher
d4-1 (B)*8 - Body ground Always 10 kΩ or higher
d8-2 (B)*9 - Body ground Always 10 kΩ or higher


*1: for 12.3 Inch Display

*2: w/ Headup Display System

*3: w/ Rear Heater

*4: w/ Pre-collision System

*5: w/ Lane Tracing Assist System

*6: Except 14 Speaker

*7: for 14 Speaker

*8: for Bulb Type

*9: for LED Type



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition

*1: except 14 speaker

*2: for 14 speaker

*3: for 12.3 Inch Display

*4: w/ Headup Display System

*5: for bulb type

*6: for LED type

Click Location & Routing(T21,B19,I8,I10,I18,I22,I21,I17,I78,I61,I62,i6,h11,P5,O5,N8,M10,d5,d9,d4,d8)Location & Routing

Click Connector(T21)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assembly

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

Click Connector(I8)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

Click Connector(I61)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Foot Light RH (No. 1 Interior Illumination Light Assembly)

Click Connector(I62)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Foot Light LH (No. 1 Interior Illumination Light Assembly)

Click Connector(i6)Seat>Front Seat Wire LH>Foot Light LH (No. 1 Interior Illumination Light Assembly LH)

Click Connector(h11)Seat>Front Seat Wire RH>Foot Light RH (No. 1 Interior Illumination Light Assembly RH)

Click Connector(P5)Body>No. 2 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly LH

Click Connector(O5)Body>No. 1 Rear Door Wire>Rear Door Inside Handle Illumination Light Assembly RH

Click Connector(N8)Body>Front Door Wire LH>Front Door Inside Handle Illumination Light Assembly LH

Click Connector(M10)Body>Front Door Wire RH>Front Door Inside Handle Illumination Light Assembly RH

Click Connector(d5)Body>No. 1 Roof Wire>Vanity Light Assembly LH

Click Connector(d9)Body>No. 1 Roof Wire>Vanity Light Assembly LH

Click Connector(d4)Body>No. 1 Roof Wire>Vanity Light Assembly RH

Click Connector(d8)Body>No. 1 Roof Wire>Vanity Light Assembly RH

T21-7 (+B) - Body ground Always 10.5 to 16 V
B19-14 (+BI1) - Body ground Always 10.5 to 16 V
I8-4 (+B1)*1 - Body ground Always 10.5 to 16 V
I10-4 (+B1)*2 - Body ground Always 10.5 to 16 V
I18-12 (B)*3 - Body ground Always 10.5 to 16 V
I22-1 (B)*3 - Body ground Always 10.5 to 16 V
I21-10 (+B) - Body ground Always 10.5 to 16 V
I17-2 (B)*4 - Body ground Always 10.5 to 16 V
I78-16 (+B) - Body ground Always 10.5 to 16 V
I61-2 (B) - Body ground Always 10.5 to 16 V
I62-2 (B) - Body ground Always 10.5 to 16 V
i6-2 - Body ground Always 10.5 to 16 V
h11-2 - Body ground Always 10.5 to 16 V
P5-2 (+) - Body ground Always 10.5 to 16 V
O5-2 (+) - Body ground Always 10.5 to 16 V
N8-2 (+) - Body ground Always 10.5 to 16 V
M10-2 (+) - Body ground Always 10.5 to 16 V
d5-1 (B)*5 - Body ground Always 10.5 to 16 V
d9-2 (B)*6 - Body ground Always 10.5 to 16 V
d4-1 (B)*5 - Body ground Always 10.5 to 16 V
d8-2 (B)*6 - Body ground Always 10.5 to 16 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: except 14 speaker

*2: for 14 speaker

*3: w/ Headup Display System

Click Location & Routing(I8,I10,I18,I22,I78)Location & Routing

Click Connector(I8)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I18)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Multi-Display Assembly

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

I8-3 (ACC1)*1 - Body ground Ignition switch ACC 10.5 to 16 V
I10-15 (ACC1)*2 - Body ground Ignition switch ACC 10.5 to 16 V
I18-24 (ACC)*3 - Body ground Ignition switch ACC 10.5 to 16 V
I22-3 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V
I78-7 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: for 12.3 Inch Display

*2: w/ Headup Display System

*3: w/ Pre-collision System

*4: w/ Rear Heater

*5: w/ Lane Tracing Assist System

Click Location & Routing(T21,I22,I17,A10,Q52,I58,I78,I71,B19,B20,I5)Location & Routing

Click Connector(T21)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Electrical Key & Tire Pressure Monitoring System Receiver Assembly

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

Click Connector(A10)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Millimeter Wave Radar Sensor Assembly

Click Connector(Q52)Instrument Panel>Floor Wire / No. 1 Cooler Wiring Harness Sub-Assembly>Cooler Control Switch Assembly

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

Click Connector(I71)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

T21-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
I22-4 (IG+)*1 - Body ground Ignition switch ON 10.5 to 16 V
I17-1 (IG)*2 - Body ground Ignition switch ON 10.5 to 16 V
A10-8 (IGB)*3 - Body ground Ignition switch ON 10.5 to 16 V
Q52-10 (IG)*4 - Body ground Ignition switch ON 10.5 to 16 V
I58-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
I78-8 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
I71-1 (IG)*5 - Body ground Ignition switch ON 10.5 to 16 V
B19-31 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
B20-45 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
I5-6 (IG+) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

5.CHECK AUDIO AND VISUAL SYSTEM
a.

Turn the ignition switch off and wait for 1 minute.


b.

Turn the ignition switch to ON.


c.

Lower the audio volume.


d.

Check if the audio and visual system operates normally.

OK:

Audio and visual system operates normally.



Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO RECEIVER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the radio receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-12 (B42) - Body ground Always 10 kΩ or higher
I57-26 (AC42) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B42)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

B42-11 (BIN) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BATTERY)

8.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Turn the ignition switch to ACC.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B42)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

B42-3 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



d.

Turn the ignition switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B42)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

B42-3 (ACC) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)

NG

12.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - POWER DISTRIBUTION BOX ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B42)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

B42-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - EACH ECU OR SENSOR)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the connector from the corresponding system ECU/sensor.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Stereo Component Equalizer Assembly
Tester Connection Condition Specified Condition

Click Location & Routing(B42,S25)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

B42-5 (BO1) - S25-15 (+B) Always Below 1 Ω
B42-5 (BO1)or S25-15 (+B) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance:
Stereo Component Amplifier Assembly
Tester Connection Condition Specified Condition

*1: for 14 Speaker

*2: Except 14 Speaker

Click Location & Routing(B42,S22)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assembly

B42-5 (BO1) - S22-1 (+B)*1 Always Below 1 Ω
B42-5 (BO1) - S22-16 (+B2)*2 Always Below 1 Ω
B42-5 (BO1)or S22-1 (+B)*1or S22-16 (+B2)*2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) (OUTPUT VOLTAGE FOR EACH SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) (OUTPUT VOLTAGE FOR EACH SYSTEM)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: for 14 Speaker

*2: Except 14 Speaker

Click Location & Routing(S25,S22)Location & Routing

Click Connector(S25)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Equalizer Assembly

Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assembly

S25-15 (+B) - Body ground Ignition switch ACC 10.5 to 16 V
S22-1 (+B)*1 - Body ground Ignition switch ACC 10.5 to 16 V
S22-16 (+B2)*2 - Body ground Ignition switch ACC 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

REPLACE EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B42)Location & Routing

Click Connector(B42)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Eco Run Vehicle Converter Assembly

B42-3 (ACC) - 5C-12 Always Below 1 Ω
B42-3 (ACC) or 5C-12 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR