Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Communication stop for "Stop and Go/Start" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Engine stop and start ECU branch wire or connector

·

Power source circuit of engine stop and start ECU

·

Engine stop and start ECU ground circuit

·

Engine stop and start ECU



WIRING DIAGRAM

C457889E08
0.188,1.25 1.083,1.563 0.896,0.313 10 false I178 0.198,1.427 1.875,1.896 1.677,0.469 10 false No. 7 Global CAN Junction Connector 1.531,0.375 2.75,0.573 1.219,0.198 10 false 3 1.542,0.906 2.646,1.115 1.104,0.208 10 false 14 5.271,1.563 5.729,1.76 0.458,0.198 10 false B37 5.281,2.125 5.74,2.323 0.458,0.198 10 false B37 5.281,2.677 5.74,2.875 0.458,0.198 10 false B38 5.292,3.229 5.75,3.427 0.458,0.198 10 false I57 5.292,3.792 5.75,3.99 0.458,0.198 10 false I57 5.292,4.344 5.75,4.542 0.458,0.198 10 false I57 5.292,4.906 5.75,5.104 0.458,0.198 10 false B37 5.281,5.458 5.74,5.656 0.458,0.198 10 false B37 5.688,5.479 6.146,5.677 0.458,0.198 10 false GND2 5.677,4.896 6.135,5.094 0.458,0.198 10 false GND1 5.677,4.375 6.135,4.573 0.458,0.198 10 false ACC 5.677,3.813 6.135,4.01 0.458,0.198 10 false IGP 5.656,3.271 6.115,3.469 0.458,0.198 10 false IGR 5.688,2.698 6.146,2.896 0.458,0.198 10 false +B 5.667,2.146 6.125,2.344 0.458,0.198 10 false BIN2 5.667,1.604 6.125,1.802 0.458,0.198 10 false BIN1 5.667,1.042 6.125,1.24 0.458,0.198 10 false CANL 5.656,0.479 6.115,0.677 0.458,0.198 10 false CANH 5.344,1.333 5.802,1.531 0.458,0.198 10 false 3 5.354,1.885 5.813,2.083 0.458,0.198 10 false 1 5.354,2.448 5.813,2.646 0.458,0.198 10 false 1 5.323,3 5.781,3.198 0.458,0.198 10 false 21 5.313,3.552 5.771,3.75 0.458,0.198 10 false 18 5.313,4.115 5.771,4.313 0.458,0.198 10 false 19 5.354,4.688 5.813,4.885 0.458,0.198 10 false 8 5.167,5.917 6.99,6.5 1.823,0.583 10 false Engine Stop and Start ECU 5.365,5.25 5.823,5.448 0.458,0.198 10 false 2 4.042,1.438 4.823,1.646 0.781,0.208 10 false BBC NO.1 4.031,1.958 4.813,2.167 0.781,0.208 10 false BBC NO.2 4.083,2.531 4.865,2.74 0.781,0.208 10 false EFI NO.1 3.938,3.094 4.958,3.323 1.021,0.229 10 false ECU-IGR NO.5 3.99,3.635 4.948,3.875 0.958,0.24 10 false ECU-IGP NO.3 4.042,4.208 5.01,4.427 0.969,0.219 10 false ECU-ACC 2.052,4.365 3.219,4.615 1.167,0.25 10 false from ACC Relay 1.792,3.781 3.302,4.156 1.51,0.375 10 false from IGP NO.1 Relay 1.792,3.229 3.26,3.521 1.469,0.292 10 false from IGR-NO.1 Relay 1.396,2.677 3.167,3.063 1.771,0.385 10 false from EFI-MAIN NO.1 Relay 2.292,2.156 3.479,2.458 1.188,0.302 10 false from Battery 2.292,1.573 3.5,1.813 1.208,0.24 10 false from Battery 5.292,1.01 5.75,1.208 0.458,0.198 10 false I57 5.302,0.479 5.76,0.677 0.458,0.198 10 false I57 5.302,0.26 5.76,0.458 0.458,0.198 10 false 13 5.313,0.781 5.771,0.979 0.458,0.198 10 false 14

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click here

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I57 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I57)Location & Routing

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

I57-13 (CANH) - I57-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the B37 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B37)Location & Routing

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B37-2 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B37-8 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B38,B37,I57)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(B37)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(I57)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Stop and Start ECU

B38-1 (+B) - Body ground Always 9.5 to 14 V
B37-1 (BIN2) - Body ground Always 9.5 to 14 V
B37-3 (BIN1) - Body ground Always 9.5 to 14 V
I57-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V
I57-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V
I57-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR