Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › CAMSHAFT
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133479 CAMSHAFT A

1HZ ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13511 1.INSTALL CAMSHAFT

a.
A326336C01
1.948,1.24 2.479,1.698 2.479,1.698 2.604,1.698 true 2.646,1.604 2.833,1.771 0.188,0.167 10 true *1
*1 Camshaft Thrust Plate


Install the camshaft thrust plate.


b.

Install the 2 camshaft bearings to the No. 1 camshaft bearing cap and No. 1 journal of the cylinder head sub-assembly.


c.
A326337C01
0.74,0.573 1.448,0.302 1.448,0.302 1.615,0.302 true 0.729,0.083 1.01,0.281 0.281,0.198 10 false *a 1.646,0.219 1.958,0.375 0.313,0.156 10 false *b
*a Upward
*b Key Groove


Place the camshaft on the cylinder head sub-assembly, facing the key groove upward.


d.
A326338C01
0.875,1.76 0.698,1.76 0.698,1.76 0.542,1.375 true 1.135,1.198 1.135,1.531 1.135,1.531 2.979,1.531 false 2.979,1.729 2.979,0.74 false 2.646,1.531 2.646,0.813 false 2.313,1.521 2.313,0.906 false 1.917,1.521 1.917,0.99 false 1.531,1.521 1.531,1.094 false 0.917,1.688 1.229,1.844 0.313,0.156 10 false *1 2.906,1.75 3.219,1.906 0.313,0.156 10 false *2
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap


Install the No. 1 camshaft bearing cap and 6 No. 2 camshaft bearing caps in their proper locations.


e.
A326335C01
0.552,1.563 0.938,1.688 0.938,1.688 0.479,1.406 true 2.167,1.344 2.302,1.552 0.135,0.208 10 false 1 1.688,0.427 1.823,0.635 0.135,0.208 10 false 2 1.771,1.5 1.906,1.708 0.135,0.208 10 false 3 1.281,0.563 1.417,0.771 0.135,0.208 10 false 4 2.583,1.198 2.719,1.406 0.135,0.208 10 false 5 2.208,0.25 2.344,0.458 0.135,0.208 10 false 6 1.292,1.688 1.417,1.896 0.125,0.208 10 false 7 0.875,0.698 1,0.906 0.125,0.208 10 false 8 2.917,1.073 3.042,1.281 0.125,0.208 10 false 9 2.5,0.125 2.688,0.333 0.188,0.208 10 false 10 0.635,1.917 0.823,2.125 0.188,0.208 10 false 11 0.208,0.917 0.396,1.125 0.188,0.208 10 false 12 3.25,0.229 3.427,0.438 0.177,0.208 10 false 13 2.896,0.01 3.083,0.198 0.188,0.188 10 false 14 0.969,1.625 1.208,1.802 0.24,0.177 10 false *a
*a No. 1 Camshaft Bearing Cap Bolt


Install and uniformly tighten the 14 camshaft bearing cap bolts in several passes in the sequence shown.

Torque:
for No. 1 camshaft bearing cap bolt : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)
for other bolt : 18.1 N*m (185 kgf*cm, 13 ft.*lbf)


Hide 11385 5.INSTALL CAMSHAFT OIL SEAL RETAINER

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the camshaft oil seal retainer and cylinder head sub-assembly.

·

Using a razor blade and gasket scraper, remove all the old packing (FIPG) material from the gasket surfaces and sealing groove.

·

Thoroughly clean all components to remove all the loose material.

·

Using a non-residue solvent, clean both sealing surfaces.



b.
A326339C01
3.125,1.198 3,1.198 3,1.198 2.719,1.063 true 3.156,1.115 3.344,1.302 0.188,0.188 10 false *a 0.625,0.188 0.833,0.344 0.208,0.156 10 false *b 1.177,0.188 1.396,0.375 0.219,0.188 10 false *c
*a Seal Packing
*b CORRECT
*c INCORRECT


Apply seal packing to the camshaft oil seal retainer as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

3.0 to 8.0 mm (0.118 to 0.315 in.)


NOTICE:

Install the camshaft oil seal retainer within 5 minutes.



c.

Install the camshaft oil seal retainer with the 4 bolts.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 13523P 6.INSTALL CAMSHAFT TIMING PULLEY