Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) sensor (VV1, 2 signal) of the intake camshaft consists of a magnet and MRE (Magnetic Resistance Element).

The VVT camshaft timing gear assembly has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction When either condition below is met:
·

The input voltage to the ECM remains below 0.3 V or higher than 4.7 V for 4 seconds when 2 or more seconds have elapsed after turning the ignition switch to ON (1 trip detection logic).

·

No VVT sensor (bank 1) signal is sent to the ECM during cranking (2 trip detection logic).


·

Open or short in VVT sensor (bank 1) circuit

·

VVT sensor (bank 1)

·

Camshaft timing gear assembly (bank 1)

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor (bank 1) is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (bank 1) circuit

·

VVT sensor (bank 1)

·

Camshaft timing gear assembly (bank 1)

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor (bank 1) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (bank 1) circuit

·

VVT sensor (bank 1)

·

Camshaft timing gear assembly (bank 1)

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0345 Camshaft Position Sensor "A" Circuit (Bank 2) When either condition below is met:
·

The input voltage to the ECM remains below 0.3 V or higher than 4.7 V for 4 seconds when 2 or more seconds have elapsed after turning the ignition switch to ON (1 trip detection logic).

·

No VVT sensor (bank 2) signal is sent to the ECM during cranking (2 trip detection logic).


·

Open or short in VVT sensor (bank 2) circuit

·

VVT sensor (bank 2)

·

Camshaft timing gear assembly (bank 2)

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) The output voltage of the VVT sensor (bank 2) is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (bank 2) circuit

·

VVT sensor (bank 2)

·

Camshaft timing gear assembly (bank 2)

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) The output voltage of the VVT sensor (bank 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (bank 2) circuit

·

VVT sensor (bank 2)

·

Camshaft timing gear assembly (bank 2)

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored

A122767E19
0.198,0.646 0.427,0.813 0.229,0.167 10 false NE 0.125,1.125 0.427,1.281 0.302,0.156 10 false VV1 0.125,1.51 0.427,1.656 0.302,0.146 10 false VV2 2.896,0.635 3.229,0.781 0.333,0.146 10 false GND 2.896,1.583 3.229,1.729 0.333,0.146 10 false GND 2.896,1.208 3.229,1.354 0.333,0.146 10 false GND 1.823,1.885 2.792,2.042 0.969,0.156 10 false 20 msec./DIV 2.75,0.344 3.26,0.5 0.51,0.156 10 false 5 V/DIV 0.042,0.021 2.365,0.208 2.323,0.188 10 false VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveform is as shown.

·

VV1 and VV2 stand for the VVT sensor signal, and NE stands for the CKP sensor signal.



Item Content
Terminal NE+ - NE-
VV1+ - VV1-
VV2+ - VV2-
Equipment Setting 5 V/DIV.
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A160377E13
0.583,2.24 0.917,2.417 0.333,0.177 10 false C24 0.583,2.406 2.167,2.583 1.583,0.177 10 false VVT Sensor (for Bank 1) 0.583,3.885 0.917,4.063 0.333,0.177 10 false C22 0.583,4.042 2.25,4.219 1.667,0.177 10 false VVT Sensor (for Bank 2) 1.521,1.198 1.74,1.354 0.219,0.156 10 false VC 1.844,1.094 1.99,1.271 0.146,0.177 10 false 3 4.792,1.094 5.073,1.271 0.281,0.177 10 false 115 4.844,1.479 5.083,1.656 0.24,0.177 10 false 69 4.844,1.854 5.083,2.031 0.24,0.177 10 false 92 1.344,1.583 1.74,1.74 0.396,0.156 10 false VVR+ 1.844,1.479 1.99,1.656 0.146,0.177 10 false 1 1.375,1.948 1.74,2.104 0.365,0.156 10 false VVR- 5.125,1.198 5.594,1.354 0.469,0.156 10 false VCV1 5.125,1.583 5.521,1.74 0.396,0.156 10 false VV1+ 5.125,1.948 5.49,2.135 0.365,0.188 10 false VV1- 4.802,2.729 5.073,2.906 0.271,0.177 10 false 113 4.844,3.104 5.083,3.281 0.24,0.177 10 false 67 4.844,3.49 5.083,3.667 0.24,0.177 10 false 90 5.125,2.865 5.594,3.021 0.469,0.156 10 false VCV2 5.125,3.25 5.521,3.406 0.396,0.156 10 false VV2+ 5.125,3.615 5.49,3.802 0.365,0.188 10 false VV2- 1.844,1.844 1.99,2.021 0.146,0.177 10 false 2 1.521,2.844 1.74,3 0.219,0.156 10 false VC 1.844,2.708 1.99,2.885 0.146,0.177 10 false 3 1.344,3.229 1.74,3.385 0.396,0.156 10 false VVL+ 1.844,3.094 1.99,3.271 0.146,0.177 10 false 1 1.375,3.594 1.74,3.75 0.365,0.156 10 false VVL- 1.844,3.458 1.99,3.635 0.146,0.177 10 false 2 5.365,4.25 5.708,4.406 0.344,0.156 10 false C39 5.365,4.385 5.729,4.542 0.365,0.156 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK VVT SENSOR (SENSOR POWER SOURCE)
a.
A203032C03
1.833,1.021 2.323,1.313 0.49,0.292 1.125,1.021 1.615,1.313 0.49,0.292 2,2.156 2.792,2.656 false 1.948,1.083 2.281,1.281 0.333,0.198 10 false C22 1.219,1.083 1.552,1.271 0.333,0.188 10 false C24 2.854,2.552 3.125,2.792 0.271,0.24 10 false VC 2.302,0.844 2.531,1.042 0.229,0.198 10 false *B 1.583,0.844 1.865,1.063 0.281,0.219 10 false *A 0.167,0.177 0.406,0.417 0.24,0.24 10 false *a
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to VVT Sensor)


Disconnect the VVT sensor connector.


b.

Turn the Ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
C22-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-1 (VVR+) - C39-69 (VV1+) Always Below 1 Ω
C24-2 (VVR-) - C39-92 (VV1-) Always Below 1 Ω
C22-1 (VVL+) - C39-67 (VV2+) Always Below 1 Ω
C22-2 (VVL-) - C39-90 (VV2-) Always Below 1 Ω
C24-1 (VVR+) or C39-69 (VV1+) - Body ground Always 10 kΩ or higher
C24-2 (VVR-) or C39-92 (VV1-) - Body ground Always 10 kΩ or higher
C22-1 (VVL+) or C39-67 (VV2+) - Body ground Always 10 kΩ or higher
C22-2 (VVL-) or C39-90 (VV2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SECURELY REINSTALL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SECURELY REINSTALL SENSOR
a.
A295942E01
0.417,1.885 0.729,2.083 0.313,0.198 10 OK 2.667,1.885 2.979,2.083 0.313,0.198 10 NG 1.688,1.573 2.396,1.771 0.708,0.198 10 Clearance

Check the VVT sensor installation.

OK:

VVT sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK VALVE TIMING

NG

4.CHECK VALVE TIMING
a.

Remove the cylinder head cover sub-assemblies RH and LH.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

A294365C01
1.625,1.021 1.792,0.344 1.792,0.344 1.625,0.802 false 2.406,1.135 2.083,1.448 2.083,1.448 2.417,0.875 false 4.917,2.135 5.031,1.313 5.031,1.313 4.927,1.802 false 5.688,2.052 5.344,2.458 5.344,2.458 5.677,1.885 false 5.354,2.448 5.646,2.042 false 1.76,0.198 2.073,0.396 0.313,0.198 10 *1 1.948,1.458 2.156,1.646 0.208,0.188 10 *1 4.99,1.156 5.302,1.354 0.313,0.198 10 *1 5.24,2.479 5.552,2.677 0.313,0.198 10 *1
*1 Timing Mark - -



b.

Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.


HINT:
·

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

·

If the result is not as specified, check mechanical parts related to valve timing for looseness in the timing chain, jumped teeth, etc.




Result:
Proceed to
OK
NG



OK

5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)

NG

5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE VVT SENSOR

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

6.REPLACE VVT SENSOR

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Clear DTCs
50002 234

i.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B