Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CAMSHAFT
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136555 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 16711 1.REMOVE FAN SHROUD

Hide 17129 2.REMOVE INTAKE AIR SURGE TANK

Hide 23801P 3.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 11201 5.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202 6.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 7.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11324 8.REMOVE TIMING CHAIN COVER PLATE

a.
A302447

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 13540 9.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13512 10.REMOVE NO. 2 CAMSHAFT

NOTICE:

As the thrust clearance of the No. 2 camshaft is small, the camshaft must be kept level while it is being removed. If the No. 2 camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the No. 2 camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.
A316657C01
2.135,1.156 2.365,1.344 0.229,0.188 10 true *a
*a Raise


While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 2 chain tensioner assembly in place.


b.
A316661

Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the bolt.

NOTICE:

Do not damage the surrounding parts.



c.

Separate the camshaft timing sprocket from the No. 2 camshaft.


d.
A316662

Rotate the No. 2 camshaft counterclockwise and set it as shown in the illustration.


e.
A316663N01
0.552,1.958 0.708,2.156 0.156,0.198 10 false 1 1.26,1.969 1.417,2.167 0.156,0.198 10 false 3 1.927,1.979 2.083,2.177 0.156,0.198 10 false 7 2.26,1.969 2.417,2.167 0.156,0.198 10 false 5 0.74,0.99 0.896,1.188 0.156,0.198 10 true 2 1.417,1 1.573,1.198 0.156,0.198 10 true 4 2.083,1 2.24,1.198 0.156,0.198 10 true 8 2.531,0.938 2.688,1.135 0.156,0.198 10 true 6

Uniformly loosen the 8 bolts in several steps in the sequence shown in the illustration and remove the bolts.


f.

Remove the 4 camshaft bearing caps and No. 2 camshaft.


Hide 13550 11.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A316664

Remove the bolt, No. 2 chain tensioner assembly and camshaft timing sprocket.


Hide 13511 12.REMOVE CAMSHAFT

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.
A326567C01
1.896,0.698 2.417,0.167 2.417,0.167 2.583,0.167 true 1.979,0.792 2.979,0.792 true 2.625,0.083 2.938,0.24 0.313,0.156 10 true *a 3.031,0.719 3.344,0.875 0.313,0.156 10 false *b
*a Paint Mark
*b Timing Mark


Mark the chain link of the chain sub-assembly with paint.

HINT:

Place the paint mark on the chain link at the location of the timing mark of the camshaft timing gear assembly.



b.
A316665

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:
·

Do not damage the surrounding parts.

·

Do not disassemble the camshaft timing gear assembly.




c.
A316666C01
2.594,1.125 2.75,1.323 0.156,0.198 10 false .
V100135

Slide


Slide the camshaft timing gear assembly and separate the chain sub-assembly from the camshaft timing gear assembly.


d.
A316667

Rotate the camshaft counterclockwise and set it as shown in the illustration.


e.
A316668N01
0.76,0.281 0.917,0.469 0.156,0.188 10 true 1 1.49,0.281 1.646,0.469 0.156,0.188 10 true 3 2.167,0.313 2.323,0.5 0.156,0.188 10 true 7 2.552,0.219 2.708,0.406 0.156,0.188 10 true 5 0.76,1.479 0.917,1.667 0.156,0.188 10 true 2 1.479,1.448 1.635,1.635 0.156,0.188 10 true 4 2.188,1.448 2.344,1.635 0.156,0.188 10 true 8 2.583,1.542 2.74,1.729 0.156,0.188 10 true 6

Uniformly loosen the 8 bolts in several steps in the sequence shown in the illustration and remove the bolts.


f.

Remove the 4 camshaft bearing caps.


g.
A316669

Remove the bolt with the camshaft lifted up, and then remove the camshaft and camshaft timing gear assembly together with the No. 2 chain sub-assembly.


h.
A316670

Tie the chain sub-assembly with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover sub-assembly.



Hide 13054 13.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

NOTICE:

As the thrust clearance of the No. 4 camshaft sub-assembly is small, the No. 4 camshaft sub-assembly must be kept level while it is being removed. If the No. 4 camshaft sub-assembly is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the No. 4 camshaft sub-assembly to seize or break. To avoid this, make sure the following steps are carried out.


a.
A316671C01
1.99,0.177 2.302,0.333 0.313,0.156 10 false *a
*a Push


While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 3 chain tensioner assembly in place.


b.
A316672

Hold the hexagonal portion of the No. 4 camshaft sub-assembly with a wrench and remove the bolt.

NOTICE:

Do not damage the surrounding parts.



c.

Separate the camshaft timing sprocket from the No. 4 camshaft sub-assembly.


d.
A316673N01
1.104,0.958 1.229,1.125 0.125,0.167 10 true 6 1.635,1.021 1.76,1.188 0.125,0.167 10 true 8 2.281,1.021 2.406,1.188 0.125,0.167 10 true 4 2.958,1.052 3.083,1.219 0.125,0.167 10 true 2 1.073,1.969 1.198,2.135 0.125,0.167 10 true 5 1.573,1.927 1.698,2.094 0.125,0.167 10 true 7 2.219,1.927 2.344,2.094 0.125,0.167 10 true 3 2.885,1.917 3.01,2.083 0.125,0.167 10 true 1

Uniformly loosen the 8 bolts in several steps in the sequence shown in the illustration and remove the bolts.


e.

Remove the 4 camshaft bearing caps and No. 4 camshaft sub-assembly.


Hide 13560A 14.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A316674

Remove the bolt, No. 3 chain tensioner assembly and camshaft timing sprocket.


Hide 13053 15.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:

As the thrust clearance of the No. 3 camshaft sub-assembly is small, the No. 3 camshaft sub-assembly must be kept level while it is being removed. If the No. 3 camshaft sub-assembly is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the No. 3 camshaft sub-assembly to seize or break. To avoid this, make sure the following steps are carried out.


a.
A326553C01
1.167,0.25 1.333,0.25 1.333,0.25 1.708,0.698 true 0.417,1.75 0.583,1.75 0.583,1.75 1.594,0.781 true 0.583,1.75 1.698,0.875 true 1,0.177 1.25,0.417 0.25,0.24 10 true *a 0.25,1.656 0.563,1.813 0.313,0.156 10 false *b
*a Paint Mark
*b Timing Mark


Mark the chain link of the chain sub-assembly with paint.

HINT:

Place the paint mark on the chain link at the location of the timing mark of the camshaft timing gear assembly.



b.
A316675

Release the chain tension between the camshaft timing gear assembly (for bank 2) and crankshaft timing sprocket by turning the crankshaft counterclockwise slightly.


c.
A316676

Hold the hexagonal portion of the No. 3 camshaft sub-assembly with a wrench and loosen the bolt.

NOTICE:
·

Do not damage the surrounding parts.

·

Do not disassemble the camshaft timing gear assembly.




d.
A316677C01
0.74,1.156 0.896,1.354 0.156,0.198 10 false .
V100135

Slide


Slide the camshaft timing gear assembly and separate the chain sub-assembly from the camshaft timing gear assembly.


e.
A316678N01
0.906,0.229 1.063,0.427 0.156,0.198 10 true 5 1.427,0.333 1.583,0.531 0.156,0.198 10 true 7 2.135,0.344 2.292,0.542 0.156,0.198 10 true 3 2.792,0.344 2.948,0.542 0.156,0.198 10 true 1 0.938,1.385 1.094,1.583 0.156,0.198 10 true 6 1.417,1.354 1.573,1.552 0.156,0.198 10 true 8 2.115,1.323 2.271,1.521 0.156,0.198 10 true 4 2.802,1.323 2.958,1.521 0.156,0.198 10 true 2

Uniformly loosen the 8 bolts in several steps in the sequence shown in the illustration and remove the bolts.


f.

Remove the 4 camshaft bearing caps.


g.
A316679

Remove the bolt with the No. 3 camshaft sub-assembly lifted up, and then remove the No. 3 camshaft sub-assembly and camshaft timing gear assembly together with the No. 2 chain sub-assembly.


h.
A316680

Tie the chain sub-assembly with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover sub-assembly.