Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A122492E36
1.417,0.5 1.917,1.5 false 2.635,1.063 2.292,1.49 false 4.698,1.26 4.073,2.156 false 5.031,1.552 5.521,2.198 false 0.115,0.302 1.76,0.677 1.646,0.375 10 false Temperature Sensor (Thermistor) 2.167,0.146 2.448,0.365 0.281,0.219 10 false B+ 2.208,0.542 3.573,0.781 1.365,0.24 10 false Power Transistor 2.646,0.958 4.75,1.156 2.104,0.198 10 false Platinum Hot Wire (Heater) 1.667,1.51 1.833,1.719 0.167,0.208 10 false A 2.469,1.51 2.656,1.708 0.188,0.198 10 false B 2.896,1.583 4.094,1.781 1.198,0.198 10 false Output Voltage 5.167,2.188 6.979,2.385 1.813,0.198 10 false Platinum Hot Wire (Heater) 2.896,2.188 5.417,2.396 2.521,0.208 10 false Temperature Sensor (Thermistor)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass or Volume Air Flow Circuit Low Input Mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass or Volume Air Flow Circuit High Input M mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Airflow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


271.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V, for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102 or P0103.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A182250E09
4.104,1.115 4.323,1.281 0.219,0.167 10 false VG 5.063,1.115 5.281,1.281 0.219,0.167 10 false VG 4.792,1.115 4.99,1.281 0.198,0.167 10 false 72 5.198,2.552 5.552,2.719 0.354,0.167 10 false C39 4.792,1.615 4.99,1.781 0.198,0.167 10 false 73 4.406,1.115 4.542,1.281 0.135,0.167 10 false 3 4.021,1.615 4.323,1.781 0.302,0.167 10 false E2G 5.073,1.615 5.375,1.781 0.302,0.167 10 false E2G 2.969,2.104 3.323,2.271 0.354,0.167 10 false C3 2.969,2.26 4.271,2.427 1.302,0.167 10 false Mass Air Flow Meter 4.406,1.615 4.542,1.781 0.135,0.167 10 false 2 2.875,0.802 3.094,0.969 0.219,0.167 10 false +B 1.74,1.031 2.385,1.198 0.646,0.167 10 false EFI NO. 2 0.365,0.875 1.354,1.26 0.99,0.385 10 false from EFI MAIN Relay 2.719,0.802 2.896,0.969 0.177,0.167 10 false 1 5.198,2.729 5.563,2.885 0.365,0.156 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0102 OR P0103)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B




A

2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE VOLTAGE)
A107942C28
0.333,1.104 0.74,1.354 0.406,0.25 1.396,1.531 1.219,1.917 1.219,1.917 1.052,1.917 true 0.792,1.854 1.104,2.052 0.313,0.198 10 false +B 0.417,1.146 0.865,1.521 0.448,0.375 10 false C3 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Mass Air Flow Meter)


a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C3-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-3 (VG) - C39-72 (VG) Always Below 1 Ω
C3-2 (E2G) - C39-73 (E2G) Always Below 1 Ω
C3-3 (VG) or C39-72 (VG) - Body ground Always 10 kΩ or higher
C3-2 (E2G) or C39-73 (E2G) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to the Inspection for mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.




Result:
Proceed to
OK
NG



OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-2 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C3-2 (E2G) - C39-73 (E2G) Always Below 1 Ω
C3-2 (E2G) or C39-73 (E2G) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR