Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving with the lock-up torque converter clutch on when the brakes are suddenly applied.

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High The stop light switch remains on even when vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminatesand the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be output.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Stop Light Switch.

Powertrain > Engine and ECT > Data List
Tester Display
Stop Light Switch
50003 234 117

e.

Read the value displayed on the GTS when the brake pedal is depressed and released.

OK:
GTS Display Measurement Item/Range
(display)
Normal Condition
Stop Light Switch Stop light switch status: ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released





Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.
A112585C08
0.823,2.594 1.25,2.833 0.427,0.24 1.906,2.594 2.344,2.844 0.438,0.25 1.865,3.667 2.625,3.406 false 0.188,0.573 0.5,0.802 0.313,0.229 10 false *a 2.698,3.333 3.354,3.563 0.656,0.229 10 false 36 (STP) 0.906,2.635 1.198,2.813 0.292,0.177 10 false I84 1.667,0.583 1.979,0.813 0.313,0.229 10 false *b 0.5,2.323 0.813,2.552 0.313,0.229 10 false *c 2.031,2.646 2.49,2.844 0.458,0.198 10 false A29 0.979,2.417 1.292,2.615 0.313,0.198 10 false *A 2.031,2.417 2.344,2.615 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I84-36 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V

for RHD
Tester Connection Condition Specified Condition
A29-36 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR