Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E73
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.781 3.323,5.01 3.323,5.01 3.854,5.01 false 4.427,0.844 5.323,1.01 0.896,0.167 10 false VVT Sensor 4.427,1.365 6.521,1.521 2.094,0.156 10 false Crankshaft Position Sensor 0.073,0.01 1.625,0.26 1.552,0.25 10 false VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 false Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 false Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 false Correction 2.823,3.208 3.229,3.385 0.406,0.177 10 false ECM 1.604,3.75 4.427,3.969 2.823,0.219 10 false Camshaft Timing Oil Control Valve Assembly 0.167,2.688 0.865,2.865 0.698,0.177 10 false Duty-cycle 4.427,1.865 6.74,2.177 2.313,0.313 10 false Mass Air Flow Meter Sub-assemnly 4.427,2.885 6.781,3.073 2.354,0.188 10 false Engine Coolant Temperature Sensor 4.427,2.365 6.208,2.531 1.781,0.167 10 false Throttle Position Sensor 4.427,3.385 6.167,3.542 1.74,0.156 10 false Vehicle Speed Sensor 0.313,4.271 1.677,4.479 1.365,0.208 10 false Engine Oil Pressure 3.656,4.219 6.302,4.406 2.646,0.188 10 false VVT Controller (Camshaft Timing Gear) 3.885,4.917 4.99,5.104 1.104,0.188 10 false Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) An open or short in the camshaft timing oil control valve assembly (for bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for bank 1) circuit

·

Camshaft timing oil control valve assembly (for bank 1)

·

ECM


Comes on DTC stored
P0020 Camshaft Position "A" Actuator Circuit (Bank 2) An open or short in the camshaft timing oil control valve assembly (for bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for bank 2) circuit

·

Camshaft timing oil control valve assembly (for bank 2)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve assembly duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010 or P0020.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A160561E14
0.573,3.729 0.896,3.885 0.323,0.156 10 false C26 0.573,1.917 4.115,2.135 3.542,0.219 10 false Camshaft Timing Oil Control Valve Assembly (for Bank 1) 1.469,0.625 1.635,0.792 0.167,0.167 10 false 1 1.469,1.375 1.635,1.542 0.167,0.167 10 false 2 0.573,1.76 0.896,1.917 0.323,0.156 10 false C27 0.573,3.885 4.75,4.146 4.177,0.26 10 false Camshaft Timing Oil Control Valve Assembly (for Bank 2) 1.469,2.583 1.635,2.75 0.167,0.167 10 false 1 1.469,3.292 1.635,3.458 0.167,0.167 10 false 2 5.167,0.625 5.396,0.771 0.229,0.146 10 false 58 5.448,0.625 5.865,0.771 0.417,0.146 10 false OC1+ 5.167,1.365 5.396,1.51 0.229,0.146 10 false 57 5.448,1.365 5.865,1.51 0.417,0.146 10 false OC1- 5.167,2.604 5.396,2.75 0.229,0.146 10 false 52 5.448,2.604 5.865,2.75 0.417,0.146 10 false OC2+ 5.167,3.333 5.396,3.479 0.229,0.146 10 false 51 5.448,3.333 5.865,3.479 0.417,0.146 10 false OC2- 5.594,4.219 5.865,4.365 0.271,0.146 10 false C39 5.594,4.375 6.021,4.521 0.427,0.146 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0010 OR P0020)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

i.

Read the DTCs.

Result:
Result Proceed to
DTC P0010 or P0020 is output A
DTC is not output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for bank 1) connector.


b.

Disconnect the camshaft timing oil control valve assembly (for bank 2) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-1 - C39-58 (OC1+) Always Below 1 Ω
C26-1 - C39-52 (OC2+) Always Below 1 Ω
C27-2 - C39-57 (OC1-) Always Below 1 Ω
C26-2 - C39-51 (OC2-) Always Below 1 Ω
C27-1 or C39-58 (OC1+) - Body ground Always 10 kΩ or higher
C26-1 or C39-52 (OC2+) - Body ground Always 10 kΩ or higher
C27-2 or C39-57 (OC1-) - Body ground Always 10 kΩ or higher
C26-2 or C39-51 (OC2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR