Home › Engine / Hybrid System › 1HZ (ENGINE CONTROL) › ECD SYSTEM
RM25T0E _51 Engine / Hybrid System _029759 1HZ ENGINE CONTROL _0135351 ECD SYSTEM C

1HZ ENGINE CONTROL  ECD SYSTEM  13  Engine Speed Sensor Circuit Malfunction (NE Circuit)  


DESCRIPTION

The pickup sensor in the engine control system contains a signal plate and pickup coil for the NE signal.

The emission control ECU detects the engine speed and the cam lift position of the injection pump. The emission control ECU uses NE signals for injection timing control. The NE signal is also used for injection volume control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
13 Engine Speed Sensor Circuit Malfunction (NE Circuit) No NE signal to emission control ECU for 0.5 seconds or more at 1000 rpm or more
·

Open or short in pickup sensor circuit

·

Pickup sensor

·

Emission control ECU


Glow Indicator Light Comes on DTC stored

Reference:

Inspection using an oscilloscope


A190772E01
2.791,1.866 3.146,2.055 0.354,0.189 10 GND 2.624,0.943 3.171,1.1 0.547,0.156 10 1 V/DIV. 0.991,2.92 1.829,3.076 0.839,0.156 10 2 msec./DIV. 0.072,1.858 0.316,2.046 0.243,0.189 10 NE

The correct waveform is as shown.

Items Contents
Terminal NE+ and NE-
Equipment Setting 1 V/DIV.
2 msec./DIV
Condition Idling

WIRING DIAGRAM

A190327E03
1.177,1.802 1.448,1.958 0.271,0.156 10 false C83 1.177,2.021 2.177,2.229 1,0.208 10 false Pickup Sensor 2.406,0.563 2.563,0.74 0.156,0.177 10 false 1 2.406,1.229 2.563,1.406 0.156,0.177 10 false 2 5.188,0.781 5.375,0.938 0.188,0.156 10 false 6 5.104,1.458 5.292,1.615 0.188,0.156 10 false 19 5.406,0.688 5.729,0.875 0.323,0.188 10 false NE+ 5.406,1.333 5.729,1.521 0.323,0.188 10 false NE- 5.479,2.031 5.802,2.188 0.323,0.156 10 false A30 5.469,2.188 7.115,2.417 1.646,0.229 10 false Emission Control ECU

PROCEDURE

1.INSPECT PICKUP SENSOR

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PICKUP SENSOR - EMISSION CONTROL ECU)

NG

2.CHECK HARNESS AND CONNECTOR (PICKUP SENSOR - EMISSION CONTROL ECU)
a.

Disconnect the emission control ECU connector.


b.

Disconnect the pickup sensor connector.


c.
A311439C02
0.521,1.146 0.927,1.49 0.406,0.344 1.302,2.417 1.708,2.76 0.406,0.344 1.583,3.656 1.948,4.073 true 0.667,4.115 1.594,3.75 true 0.188,0.406 0.5,0.604 0.313,0.198 10 false *a 0.177,2.375 0.49,2.573 0.313,0.198 10 false *b 0.531,4.135 1.302,4.552 0.771,0.417 10 false 19 (NE-) 1.917,4.115 2.813,4.563 0.896,0.448 10 false 6 (NE+) 0.615,1.229 1.073,1.427 0.458,0.198 10 false C83 1.385,2.51 1.844,2.708 0.458,0.198 10 false A30
*a Front view of wire harness connector
(to Pickup Sensor)
*b Rear view of wire harness connector
(to Emission Control ECU)


Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-1 - A30-6 (NE+) Always Below 1 Ω
C83-2 - A30-19 (NE-) Always Below 1 Ω
C83-1 or A30-6 (NE+) - Body ground Always 10 kΩ or higher
C83-2 or A30-19 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
a.

Check the pickup sensor installation.

OK:

Sensor is installed securely.



Result:
Proceed to
OK
NG



OK

NG

SECURELY REINSTALL PICKUP SENSOR