Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM. When the ignition switch is turned ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A182518E08
6.198,2.427 6.563,2.583 0.365,0.156 10 false A29 6.198,2.583 6.594,2.74 0.396,0.156 10 false ECM 6.031,1.01 6.25,1.167 0.219,0.156 10 false W 5.76,1.01 5.958,1.167 0.198,0.156 10 false 24 4.896,1.125 5.219,1.281 0.323,0.156 10 false L26 4.948,0.927 5.146,1.083 0.198,0.156 10 false 21 2.708,1.125 3.031,1.281 0.323,0.156 10 false L25 2.771,0.906 2.969,1.063 0.198,0.156 10 false 28 3.708,1.281 4,1.448 0.292,0.167 10 false MIL 4.51,1.229 4.844,1.396 0.333,0.167 10 false CHK 3.063,1.229 3.271,1.396 0.208,0.167 10 false B 1.99,1.25 2.344,1.417 0.354,0.167 10 false MET 3.375,2.083 4.625,2.25 1.25,0.167 10 false Combination Meter 0.188,1.104 1.438,1.302 1.25,0.198 10 false from Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Check if DTCs have been stored .If DTCs are present, write them down.



e.

Check that the MIL turns OFF.

Standard:

MIL turns OFF.



Result:
Proceed to
OK
NG



OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166420C02
1.448,0.792 1.875,1.083 0.427,0.292 0.229,0.125 0.406,0.323 0.177,0.198 10 false *a 1.531,0.865 1.844,1.021 0.313,0.156 10 false A29
*a Front view of wire harness connector
(to ECM)


Disconnect the A29 ECM connector.


b.

Turn the ignition switch ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the L26 combination meter connector.


b.

Disconnect the A29 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L26-21 (CHK) - A29-24 (W) Always Below 1 Ω
L26-21 (CHK) or A29-24 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned ON.

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.CHECK COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

See the combination meter troubleshooting procedure.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY