The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Connect the GTS to the DLC3.
Turn the ignition switch ON and GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
B
A
Disconnect the C50 throttle position sensor (for Bank 1) connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C50 throttle position sensor (for Bank 1) connector.
B
A
Disconnect the C65 throttle position sensor (for Bank 2) connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C65 throttle position sensor (for Bank 2) connector.
B
A
Disconnect the C47 No. 1 EGR valve connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C47 No. 1 EGR valve connector.
B
A
Disconnect the C66 No. 2 EGR valve connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C66 No. 2 EGR valve connector.
B
A
Disconnect the I43 accelerator pedal position sensor connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the I43 accelerator pedal position sensor connector.
B
A
Disconnect the C59 manifold absolute pressure sensor connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C59 manifold absolute pressure sensor connector.
B
A
Disconnect the C56 fuel pressure sensor connector.
Turn the ignition switch ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C56 fuel pressure sensor connector.
B
A
| *a | Front view of wire harness connector (to ECM) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the throttle position sensor (for Bank 1) connector.
Disconnect the throttle position sensor (for Bank 2) connector.
Disconnect the No. 1 EGR valve connector.
Disconnect the No. 2 EGR valve connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the A29 and C39 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-90 (VCEG) - Body ground | Always | 10 kΩ or higher |
| C39-91 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C39-70 (VCM) - Body ground | Always | 10 kΩ or higher |
| C39-66 (VCPM) - Body ground | Always | 10 kΩ or higher |
| A29-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A29-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle position sensor (for Bank 1) connector.
Reconnect the throttle position sensor (for Bank 2) connector.
Reconnect the No. 1 EGR valve connector.
Reconnect the No. 2 EGR valve connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connectors.
| Proceed to |
| OK |
| NG |
OK
NG