Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.

The G signal plate (timing sprocket) has one tooth on its outer circumference and is installed on the camshaft timing chain gear. When the timing gear rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.

The NE signal plate has 34 teeth and is mounted on the crank angle sensor plate. The NE signal sensor generates 34 signals for every engine revolution. The ECM detects the standard crankshaft angle based on the G signal, and detects the actual crankshaft angle and engine speed based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) STA ON:
No camshaft position sensor signal to ECM while cranking for 4 seconds or more
STA OFF:
·

G signal not input with engine speed of 500 rpm or more

·

No camshaft position sensor signal to ECM with engine speed of 500 to 3000 rpm 20 times or more


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

No. 2 camshaft timing sprocket

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR
a.
A165742C01
0.229,0.281 2.719,0.635 2.49,0.354 10 false *a
*a Component without harness connected
(Camshaft Position Sensor)


Disconnect the C68 camshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 Cold 835 to 1400 Ω
1 - 2 Hot 1060 to 1645 Ω


HINT:

In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.
A311466C02
1.313,2.333 1.729,2.656 0.417,0.323 1.5,0.115 1.917,0.438 0.417,0.323 1.25,4.208 1.813,3.51 true 2.271,4.219 1.885,3.51 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.177,2.031 0.49,2.188 0.313,0.156 10 false *b 1.396,2.417 1.708,2.573 0.313,0.156 10 false C39 1.583,0.198 1.896,0.354 0.313,0.156 10 false C68 1.052,4.229 1.656,4.417 0.604,0.188 10 false 79 (G-) 2.083,4.25 2.667,4.427 0.583,0.177 10 false 80 (G+)
*a Front view of wire harness connector
(to Camshaft Position Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C68 camshaft position sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C68-1 - C39-80 (G+) Always Below 1 Ω
C68-2 - C39-79 (G-) Always Below 1 Ω
C68-1 or C39-80 (G+) - Body ground Always 10 kΩ or higher
C68-2 or C39-79 (G-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET

NG

4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET
a.

Check the condition of the timing sprocket.

OK:

Timing sprocket does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 CAMSHAFT TIMING SPROCKET