Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the common rail injection system is controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit When one of following conditions is met:
(1 trip detection logic)
·

No crankshaft position sensor signal to ECM while cranking

·

When normal G signal is input, malfunctioning NE signal is input

·

No crankshaft position sensor signal to ECM at engine speed of 600 rpm or more


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent No crankshaft position sensor signal is input to ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met:
(1 trip detection logic)
(a) Engine speed is at 1000 rpm or more
(b) STA signal is OFF
(c) 3 seconds or more have elapsed after STA signal is switched from ON to OFF
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft

·

ECM


- DTC stored

WIRING DIAGRAM

A165739E14
0.573,1.625 0.927,1.771 0.354,0.146 10 false C68 0.573,1.802 2.24,1.979 1.667,0.177 10 false Camshaft Position Sensor 0.573,3.927 0.927,4.073 0.354,0.146 10 false C42 0.573,4.104 2.365,4.281 1.792,0.177 10 false Crankshaft Position Sensor 1.135,2.635 1.469,2.781 0.333,0.146 10 false NE+ 1.521,2.635 1.698,2.781 0.177,0.146 10 false 1 2.76,2.229 2.938,2.375 0.177,0.146 10 false * 0.344,4.469 1.104,4.635 0.76,0.167 10 false *: Shielded 3.5,0.25 3.677,0.396 0.177,0.146 10 false * 1.135,3.333 1.469,3.479 0.333,0.146 10 false NE- 5.51,2.635 5.844,2.781 0.333,0.146 10 false NE+ 5.219,2.635 5.427,2.823 0.208,0.188 10 false 78 5.51,3.333 5.844,3.479 0.333,0.146 10 false NE- 5.927,4.021 6.26,4.167 0.333,0.146 10 false C39 5.927,4.188 6.313,4.385 0.385,0.198 10 false ECM 5.219,3.333 5.448,3.479 0.229,0.146 10 false 77 5.51,0.667 5.844,0.813 0.333,0.146 10 false G+ 5.219,0.667 5.427,0.854 0.208,0.188 10 false 80 5.51,1.365 5.844,1.51 0.333,0.146 10 false G- 5.219,1.365 5.448,1.51 0.229,0.146 10 false 79 1.521,3.333 1.698,3.479 0.177,0.146 10 false 2 1.521,0.656 1.698,0.802 0.177,0.146 10 false 1 1.521,1.365 1.698,1.51 0.177,0.146 10 false 2 1.104,3.604 1.438,3.75 0.333,0.146 10 false GND 1.521,3.688 1.698,3.833 0.177,0.146 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CRANKSHAFT POSITION
a.
A165740C03
1.125,1.521 1.427,2.094 true 2.292,1.531 1.979,2.125 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.021,1.333 1.333,1.49 0.313,0.156 10 false NE- 2.188,1.344 2.5,1.5 0.313,0.156 10 false NE+
*a Component without harness connected
(Crankshaft Position Sensor)


Disconnect the C42 crankshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 (NE+) - 2 (NE-) Cold 1630 to 2740 Ω
1 (NE+) - 2 (NE-) Hot 2065 to 3225 Ω


HINT:

In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



Result:
Proceed to
OK
NG



OK

2.CHECK CRANKSHAFT POSITION SENSOR - ECM

NG

2.CHECK CRANKSHAFT POSITION SENSOR - ECM
a.
A311465C02
1.5,0.313 1.927,0.615 0.427,0.302 1.26,2.323 1.688,2.625 0.427,0.302 1.01,1.646 1.542,1.302 true 2.417,1.646 1.885,1.313 true 1.167,4.198 1.698,3.51 true 2.229,4.219 1.781,3.5 true 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 0.167,2.104 0.479,2.26 0.313,0.156 10 false *b 2.365,1.667 2.677,1.823 0.313,0.156 10 false NE- 0.854,1.667 1.167,1.823 0.313,0.156 10 false NE+ 1.354,2.396 1.667,2.552 0.313,0.156 10 false C39 1.594,0.385 1.906,0.542 0.313,0.156 10 false C42 2.031,4.24 2.656,4.396 0.625,0.156 10 false 78 (NE+) 0.917,4.25 1.625,4.406 0.708,0.156 10 false 77 (NE-)
*a Front view of wire harness connector
(to Crankshaft Position Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C42 crankshaft position sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C42-1 (NE+) - C39-78 (NE+) Always Below 1 Ω
C42-2 (NE-) - C39-77 (NE-) Always Below 1 Ω
C42-1 (NE+) or C39-78 (NE+) - Body ground Always 10 kΩ or higher
C42-2 (NE-) or C39-77 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CRANK POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CRANK POSITION SENSOR (SENSOR INSTALLATION)
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE

NG

4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the sensor plate.

OK:

The sensor plate's teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

NG