Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2120

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance Condition (a) continues for 2 seconds:
(a) Difference between VPA1 and VPA2 exceeds the threshold
(1 trip detection logic)
·

Accelerator pedal position sensor circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.

Connect the GTS to the DLC3.


b.
C129061C23
0.698,1.635 1.448,1.844 0.75,0.208 10 false *a 0.292,0.115 1.625,0.323 1.333,0.208 10 false *1 2.26,1.615 2.927,1.823 0.667,0.208 10 false *b
*1 Accelerator Pedal
*a Depressed
*b Released


Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor out No. 1 and Accel Sensor out No. 1.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 61 412,413

d.

Read the values.

Standard voltage:
Accelerator Pedal Accel Sensor out No. 1 Accel Sensor out No. 2
Released 0.6 to 1.0 V 1.4 to 1.8 V
Depressed 3.4 to 3.8 V 4.2 to 4.6 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR POSITION SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR POSITION SENSOR ASSEMBLY - ECM)
a.
A311474C03
1.563,2.479 2.01,2.75 0.448,0.271 1.49,0.219 1.938,0.49 0.448,0.271 0.688,1.281 1.354,1.125 true 1.365,1.688 1.667,1.146 true 0.896,1.51 1.542,1.146 true 1.844,1.688 1.792,1.135 true 1.917,1.156 2.219,1.531 true 2.063,1.135 2.563,1.406 true 1.823,3.781 0.646,3.615 true 1.917,3.781 0.802,4.125 true 2.01,3.781 1.125,4.302 true 2.083,3.781 1.583,4.375 true 2.26,3.781 2.625,4.094 true 2.188,3.781 2.125,4.208 true 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 0.177,2.448 0.49,2.646 0.313,0.198 10 false *b 1.656,2.552 1.979,2.74 0.323,0.188 10 false A29 1.615,0.281 1.865,0.448 0.25,0.167 10 false I43 0.271,1.219 0.885,1.417 0.615,0.198 10 false VCP2 0.615,1.521 1.229,1.719 0.615,0.198 10 false EPA2 1.208,1.719 1.823,1.917 0.615,0.198 10 false VPA2 1.781,1.729 2.396,1.927 0.615,0.198 10 false VCPA 2.24,1.563 2.854,1.76 0.615,0.198 10 false EPA 2.625,1.406 3.24,1.604 0.615,0.198 10 false VPA 0.104,4.073 1.031,4.344 0.927,0.271 10 false 54 (VPA2) 0.063,3.51 0.74,3.802 0.677,0.292 10 false 53 (VPA) 0.698,4.323 1.792,4.583 1.094,0.26 10 false 55 (VCPA) 1.448,4.406 2.823,4.604 1.375,0.198 10 false 56 (VCP2) 1.938,4.24 3.313,4.438 1.375,0.198 10 false 57 (EPA) 2.5,4.115 3.323,4.344 0.823,0.229 10 false 58 (EPA2)
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)
*b Front view of wire harness connector
(to ECM)


Disconnect the I43 accelerator pedal sensor aseembly connector.


b.

Disconnect the A29 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
I43-1 (VCP2) - A29-56 (VCP2) Always Below 1 Ω
I43-2 (EPA2) - A29-58 (EPA2) Always Below 1 Ω
I43-3 (VPA2) - A29-54 (VPA2) Always Below 1 Ω
I43-4 (VCPA) - A29-55 (VCPA) Always Below 1 Ω
I43-5 (EPA) - A29-57 (EPA) Always Below 1 Ω
I43-6 (VPA) - A29-53 (VPA) Always Below 1 Ω
I43-1 (VCP2) or A29-56 (VCP2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or A29-58 (EPA2) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or A29-54 (VPA2) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or A29-55 (VCPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or A29-57 (EPA) - Body ground Always 10 kΩ or higher
I43-6 (VPA) or A29-53 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Clear the DTC.


e.

Start the engine.


f.

Allow the engine to idle for 15 seconds.


g.

Depress and release the accelerator pedal several times.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

i.

Read the DTC.

Result:
Result Proceed to
P2121 is output A
No DTC is output B




A

B

END