Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs the voltage in proportion to the internal fuel pressure.

A168838E01
1.13,0.857 2.352,1.026 1.222,0.170 10 Output Voltage (V) 3.284,2.243 4.648,2.435 1.364,0.192 10 Fuel Pressure (MPa) 3.202,1.914 3.323,2.063 0.121,0.149 10 0 3.391,1.914 3.596,2.070 0.205,0.155 10 30 3.812,1.914 4.002,2.077 0.191,0.163 10 90 4.324,1.914 4.619,2.077 0.295,0.163 10 180 4.582,1.914 4.877,2.077 0.295,0.163 10 190 2.675,1.338 2.928,1.501 0.253,0.163 10 1.0 2.596,1.181 2.929,1.343 0.333,0.163 10 1.48 2.596,0.892 2.911,1.062 0.316,0.170 10 2.44 2.596,0.479 2.911,0.635 0.316,0.156 10 3.88 2.596,0.315 2.918,0.485 0.323,0.170 10 4.04 0.071,0 1.603,0.170 1.532,0.170 10 Property Output Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0087 Fuel Rail / System Pressure - Too Low Fuel pressure sensor output voltage stays at fixed value
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Common rail RH (fuel pressure sensor)

·

ECM


Comes on DTC stored
P0190 Fuel Rail Pressure Sensor Circuit Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or more for 0.5 seconds
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Common rail RH (fuel pressure sensor)

·

ECM


Comes on DTC stored
P0192 Fuel Rail Pressure Sensor Circuit Low Input Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Common rail RH (fuel pressure sensor)

·

ECM


Comes on DTC stored
P0193 Fuel Rail Pressure Sensor Circuit High Input Fuel pressure sensor output voltage is 4.9 V or more for 0.5 seconds
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Common rail RH (fuel pressure sensor)

·

ECM


Comes on DTC stored

HINT:
·

For more information on the fuel pressure sensor and common rail system, refer to the system description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION

·

When DTC P0087, P0190, P0192 and/or P0193 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.



Reference:
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa

MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):

Under normal conditions, the internal fuel pressure of the common rail usually fluctuates 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when the driving conditions are constant. The internal fuel pressure is approximately 27000 to 37000 kPa (275 to 377 kgf/cm2, 3915 to 5365 psi) when idling, and it increases to approximately 5000 to 70000 kPa (510 to 714 kgf/cm2, 7250 to 10150 psi) when running the engine at 2500 rpm. This DTC is set if there is no fluctuation of the fuel pressure.

If this DTC is set, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned OFF.

C129049E04
4.438,0.865 4.667,0.448 false 4.323,1.667 4.094,1.25 false 3.156,3.479 3.385,3.063 false 4,3.844 4.229,3.427 false 4.229,4.781 3.906,4.531 false 0.333,0.021 2.646,0.229 2.313,0.208 10 false P0087 Malfunction Detection 0.729,0.979 1.688,1.198 0.958,0.219 10 false Fuel Pressure 4.375,1.615 5.042,1.813 0.667,0.198 10 false Abnormal 4.729,0.344 5.313,0.542 0.583,0.198 10 false Normal 0.729,2.26 1.677,2.469 0.948,0.208 10 false Engine Speed 0.792,3.063 1.271,3.271 0.479,0.208 10 false Idling 3.427,2.948 6.5,3.146 3.073,0.198 10 false Delay of approximately 0.5 to 1.0 second 1.198,4.083 2.188,4.271 0.99,0.188 10 false Fuel Pressure 1.052,5.125 2.198,5.552 1.146,0.427 10 false Accelerator Pedal Opening Angle 2.438,5.156 2.979,5.354 0.542,0.198 10 false Closed 3.229,4.583 3.677,4.781 0.448,0.198 10 false Open 4.271,4.708 5.042,4.906 0.771,0.198 10 false Abnormal 4.281,3.333 4.875,3.552 0.594,0.219 10 false Normal 4.135,5.156 4.708,5.354 0.573,0.198 10 false Closed


P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are set if the fuel pressure sensor output voltage is out of the standard range and an open or short malfunction of the sensor circuit has occurred.

If these DTCs are set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned OFF.


WIRING DIAGRAM

A130470E07
0.563,3.292 1.958,3.49 1.396,0.198 10 false Fuel Pressure Sensor 0.563,3.125 0.875,3.323 0.313,0.198 10 false C56 1.833,1.125 2.073,1.323 0.24,0.198 10 false VC 1.854,1.875 2.083,2.073 0.229,0.198 9 false PR 1.875,2.615 2.073,2.813 0.198,0.198 10 false E2 2.167,2.833 2.333,3.063 0.167,0.229 10 false 1 5.135,2.833 5.354,3.063 0.219,0.229 10 false 75 2.167,2.083 2.333,2.313 0.167,0.229 10 false 2 5.135,2.083 5.333,2.313 0.198,0.229 10 false 69 2.167,1.333 2.333,1.563 0.167,0.229 10 false 3 5.135,1.344 5.344,1.573 0.208,0.229 10 false 70 5.427,1.115 5.844,1.313 0.417,0.198 10 false VCM 5.427,1.865 5.833,2.063 0.406,0.198 10 false PCR1 5.417,2.625 5.719,2.823 0.302,0.198 10 false E2 5.948,3.292 6.313,3.49 0.365,0.198 10 false ECM 5.948,3.125 6.313,3.323 0.365,0.198 10 false C39

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

After completing repairs, check that P0087, P0190, P0192 and/or P0193 is not set again.

·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (FUEL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT/ Data List / Fuel Press.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Press
50003 61 54

d.

Read the values.

OK:

The internal fuel pressure of the common rail iswithin the specification below.


Reference:
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa



Result:
Proceed to
OK
NG



OK

2.CHECK IF DTC OUTPUT RECURS

NG

3.HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
2.CHECK IF DTC OUTPUT RECURS

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS ON.


d.

Let the engine idle for 60 seconds, and then repeat quick engine RPM accelerations (to 2500 rpm) for 30 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0087, P0190, P0192 or P0193 is output A
No DTC is output B




A

B

3.HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.
A311456C04
1.458,0.146 1.854,0.375 0.396,0.229 1.323,2.313 1.719,2.542 0.396,0.229 1.177,1.604 1.458,1.094 false 2.135,1.615 1.875,1.104 false 1.667,1.615 1.667,1.104 false 0.531,4.177 0.906,3.396 false 1.365,4.188 0.99,3.396 false 2.063,4.167 1.427,3.396 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.125,2.021 0.438,2.219 0.313,0.198 10 false *b 1.542,0.177 1.854,0.375 0.313,0.198 10 false C56 1.094,1.646 1.406,1.844 0.313,0.198 10 false E2 1.583,1.646 1.896,1.844 0.313,0.198 10 false PR 2.083,1.646 2.396,1.844 0.313,0.198 10 false VC 1.396,2.344 1.708,2.542 0.313,0.198 10 false C39 0.396,4.208 1.104,4.479 0.708,0.271 10 false 69 (PCR1) 1.25,4.208 1.906,4.542 0.656,0.333 10 false 70 (VCM) 2.01,4.208 2.594,4.427 0.583,0.219 10 false 75 (E2)
*a Front view of wire harness connector
(to Fuel Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C56 fuel pressure sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C56-2 (PR) - C39-69 (PCR1) Always Below 1 Ω
C56-3 (VC) - C39-70 (VCM) Always Below 1 Ω
C56-1 (E2) - C39-75 (E2) Always Below 1 Ω
C56-2 (PR) or C39-69 (PCR1) - Body ground Always 10 kΩ or higher
C56-3 (VC) or C39-70 (VCM) - Body ground Always 10 kΩ or higher
C56-1 (E2) or C39-75 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR