Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

Refer to the SYSTEM DESCRIPTION.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0093 Fuel System Leak Detected - Large Leak Fuel leaks in high-pressure areas
(1 trip detection logic)
·

Fuel line between fuel supply pump and common rail

·

Fuel line between common rail and injector

·

Fuel supply pump

·

Common rail LH (pressure limiter)

·

Injector (P1238 set simultaneously)

·

Open or short in EDU circuit (P062D and/or P062E set simultaneously)

·

Open or short in injector circuit (P062D, P062E and/or P1238 set simultaneously)

·

EDU (P062D and/or P062E set simultaneously)

·

Fuel line (air bleeding)

·

ECM


Comes on DTC stored

HINT:
·

For more information on the common rail system, refer to the system description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION

·

If DTC P0093 is present, refer to the "Diagnostic Trouble Code (DTC) Table for Common Rail System".

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.


Reference
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa


MONITOR DESCRIPTION

P0093 (Fuel leaks in high-pressure areas):

This DTC indicates that fuel leaks exist in highly-pressurized areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM sets this DTC if the drop in the internal fuel pressure is large when the fuel is injected.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump, common rail, injectors, and piping. The ECM adjusts the suction control valve opening angle to obtain the desired fuel pressure.

If this DTC is set, the ECM enters fail-safe mode. The fail-safe mode suspends both fuel injection and fuel supply pump operation, and then stops the engine. Before stopping the engine, the ECM permits the vehicle to be driven for 30 second. The fail-safe mode continues until the ignition switch is turned to OFF.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0093 A
P0093 and P1238 B
P0093, P062D and/or P062E C




A

2.CHECK FOR FUEL LEAK (IN HIGH-PRESSURE FUEL PARTS AND AREA)

B

5.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)

C

2.CHECK FOR FUEL LEAK (IN HIGH-PRESSURE FUEL PARTS AND AREA)
a.

Visually check the fuel supply pump, each injector and fuel line located between the fuel supply pump and common rail for fuel leaks or fuel pressure leaks. Also, perform the same check on the fuel lines between the common rail and each injector.

HINT:

There is possibility that fuel leaks inside the components (fuel supply pump, etc.) have occurred.


OK:

No leakage



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)

NG

REPAIR OR REPLACE FUEL PARTS AND AREA

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Check the fuel receiver gauge. If the indicator is illuminated, add fuel.


b.

Operate the hand pump of the fuel filter, and bleed air from the fuel line.


c.

Connect the GTS to the DLC3.



e.

Start the engine, and rev the engine at full throttle several times.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

g.

Read the DTC.

Result:
Result Proceed to
P0093 is output A
No DTC is output B




A

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)

B

DTC CAUSED BY RUNNING OUT OF FUEL

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Start the engine, and allow the engine to idle for 20 seconds or more.


b.

Stop the engine, and wait for 15 seconds or more.


c.

Perform the procedures above 3 times or more in succession.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

e.

Read the DTC.

Result:
Result Proceed to
P0093 is output A
No DTC is output B


HINT:

If the MIL turns OFF, rev the engine at full throttle several times.




A

5.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)

B

DTC CAUSED BY RUNNING OUT OF FUEL

5.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #8.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 368,369,370,371,372,373,374,375

e.

Read the values.

Standard value:

Compensatory injection volume is between -3.0 mm3/st and 3.0 mm3/st.


HINT:
·

If the injector is malfunctioning, the compensatory injection volume remains at -5.0 mm3/st or 5.0 mm3/st.

·

The compensatory injection volume is usually between -3.0 mm3/st and 3.0 mm3/st.

·

Any cylinders that have a higher compensatory injection volume than shown above are considered to be faulty.




Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (FUEL LEAK TEST)

NG

6.PERFORM ACTIVE TEST USING GTS (FUEL LEAK TEST)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.

Powertrain > Engine and ECT > Active Test
Tester Display
Test the Fuel Leak
50004 61 90

d.

Check for fuel leaks in the high-pressure areas.

OK:

No leakage.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093 OUTPUT AREA)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093 OUTPUT AREA)

b.

Allow the engine to idle for 1 minute and then run it at 2500 rpm for 30 seconds.


c.

Connect the GTS to the DLC3.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

e.

Read the DTC.

Result:
Result Proceed to
P0093 is output A
No DTC is output B




A

8.REPLACE COMMON RAIL LH (PRESSURE LIMITER)

B

END

8.REPLACE COMMON RAIL LH (PRESSURE LIMITER)

Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093 OUTPUT AREA)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093 OUTPUT AREA)
HINT:
·

After clearing DTCs, allow the engine to idle for 1 minute and then run it at 2500 rpm for 30 seconds.

·

At the same time, check the fuel pressure inside the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.

·

The internal fuel pressure of the common rail must be stable under each driving condition.



Reference:
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa


Result:
Proceed to
NEXT



NEXT

END