Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0400  Exhaust Gas Recirculation Flow  P1248  Exhaust Gas Recirculation Flow Bank 2  


DESCRIPTION

The EGR system recirculates exhaust gases in order to suit every driving condition. The recirculated gas mingles with the intake air so that the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.

In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve angle.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0400 Exhaust Gas Recirculation Flow When one of the following conditions is met:
·

Target and actual positions of the electric EGR control valve are different

(1 trip detection logic)

·

Mass air flow rate is not changed when turning on electric EGR control valve

(2 trip detection logic)


·

EGR valve stuck

·

EGR valve does not move smoothly

·

Open or short in EGR valve circuit

·

EGR valve deposit

·

EGR valve passage

·

ECM


Comes on DTC stored
P1248 Exhaust Gas Recirculation Flow Bank 2 Target and actual positions of the electric EGR control valve are different
(1 trip detection logic)
·

EGR valve stuck

·

EGR valve does not move smoothly

·

Open or short in EGR valve circuit

·

EGR valve deposit

·

EGR valve passage

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

·

When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the EGR valve and illuminates the MIL (1 trip detection logic).

·

If the electric EGR control valve is forcibly operated but the intake air amount does not vary, the ECM determines that the electric EGR control valve is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).


WIRING DIAGRAM

A165763E05
0.281,2.479 1.333,2.833 1.052,0.354 10 false from MAIN Relay Terminal 3 3.417,0.781 3.656,0.938 0.24,0.156 10 false VC 3.74,0.99 3.885,1.135 0.146,0.146 10 false 3 3.427,1.969 3.667,2.125 0.24,0.156 10 false E2 3.74,2.188 3.885,2.333 0.146,0.146 10 false 2 3.323,2.573 3.656,2.729 0.333,0.156 10 false EGR 2.052,2.573 2.292,2.729 0.24,0.156 10 false +B 3.74,2.667 3.885,2.813 0.146,0.146 10 false 5 1.865,2.667 2.01,2.813 0.146,0.146 10 false 1 3.25,1.271 3.656,1.427 0.406,0.156 10 false EGLS 5.646,0.781 6.135,0.938 0.49,0.156 10 false VCEG 5.646,1.979 6.115,2.135 0.469,0.156 10 false EEGL 5.646,2.573 6.083,2.729 0.438,0.156 10 false EGRS 5.646,1.271 6.052,1.427 0.406,0.156 10 false EGLS 3.74,1.479 3.885,1.625 0.146,0.146 10 false 4 5.354,0.99 5.542,1.135 0.188,0.146 10 false 90 5.365,2.188 5.552,2.333 0.188,0.146 10 false 87 5.281,2.667 5.552,2.813 0.271,0.146 10 false 107 5.646,4.948 6.115,5.104 0.469,0.156 10 false EGS2 5.646,6.25 6.083,6.406 0.438,0.156 10 false ERS2 5.365,5.146 5.552,5.292 0.188,0.146 10 false 88 5.281,6.333 5.552,6.479 0.271,0.146 10 false 108 6.156,6.875 6.427,7.021 0.271,0.146 10 false C39 6.156,7.021 6.521,7.167 0.365,0.146 10 false ECM 5.365,1.479 5.552,1.625 0.188,0.146 10 false 89 2.354,3.063 2.656,3.229 0.302,0.167 10 false C47 2.354,3.25 3.458,3.417 1.104,0.167 10 false No. 1 EGR Valve 3.417,4.448 3.656,4.604 0.24,0.156 10 false VC 3.74,4.656 3.885,4.802 0.146,0.146 10 false 3 3.448,5.625 3.688,5.781 0.24,0.156 10 false E2 3.74,5.854 3.885,6 0.146,0.146 10 false 2 3.25,6.25 3.667,6.417 0.417,0.167 10 false EGR2 2.052,6.25 2.292,6.406 0.24,0.156 10 false +B 3.74,6.333 3.885,6.479 0.146,0.146 10 false 5 1.865,6.333 2.01,6.479 0.146,0.146 10 false 1 3.25,4.938 3.656,5.094 0.406,0.156 10 false EGLS 3.74,5.146 3.885,5.292 0.146,0.146 10 false 4 2.354,6.74 2.656,6.906 0.302,0.167 10 false C66 2.354,6.917 3.479,7.083 1.125,0.167 10 false No. 2 EGR Valve 0.229,6.125 1.406,6.479 1.177,0.354 10 false from MAIN 2 Relay Terminal 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

After warming up the engine, DTC P0400 and P1248 can be set if 1 second or more passes after quickly accelerating the engine from idling.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0400, P1248)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0400 and/or P1248 are output A
P0400, P1248 and other DTCs are output B


HINT:

If codes other than P0400 and P1248 are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING GTS (EGR ANGLE)

B

2.READ VALUE USING GTS (EGR ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Actual EGR Valve Pos. and Actual EGR Valve Pos.#2

Powertrain > Engine and ECT > Data List
Tester Display
Actual EGR Valve Pos.
Actual EGR Valve Pos. #2
50003 61 578,579

e.

Read the value.

Result:
Condition Result Proceed to
After warming up the engine, quickly accelerate the engine from idle to 3000 rpm by using the accelerator pedal Constant or changes slowly A
Smooth change from approximately 0% to approximately 80% B




A

3.INSPECT EGR VALVE ASSEMBLY (RESISTANCE)

B

3.INSPECT EGR VALVE ASSEMBLY (RESISTANCE)
a.
A165764C03
1.125,2.135 0.885,2.479 true 2.292,2.104 2.531,2.458 true 0.708,2.479 1.271,2.656 0.563,0.177 10 false EGR *1 2.469,2.479 2.688,2.646 0.219,0.167 10 false +B 0.271,0.219 0.583,0.375 0.313,0.156 10 false *a 0.698,2.667 1.313,2.833 0.615,0.167 10 false EGR2 *2
*1 No. 1
*2 No. 2
*a Component without harness connected
(EGR Valve)


Disconnect the C47 or C66 EGR valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
No. 1
Tester Connection Condition Specified Condition
1 (+B) - 5 (EGR) 20°C (68°F) Approximately 6.5 to 7.5 Ω

No. 2
Tester Connection Condition Specified Condition
1 (+B) - 5 (EGR2) 20°C (68°F) Approximately 6.5 to 7.5 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE - ECM)

NG

REPLACE EGR VALVE ASSEMBLY (NO. 1 OR NO. 2)

4.CHECK HARNESS AND CONNECTOR (EGR VALVE - ECM)
a.
A311467C03
1.135,0.375 1.552,0.635 0.417,0.26 1.875,0.375 2.292,0.635 0.417,0.26 1.219,2.375 1.635,2.635 0.417,0.26 2.396,1.708 2.104,1.208 true 1.917,4.25 2.344,3.677 true 2.781,4.271 2.438,3.677 true 1.583,0.208 1.896,0.365 0.313,0.156 10 false *1 2.313,0.219 2.625,0.375 0.313,0.156 10 false *2 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 0.219,2.115 0.531,2.271 0.313,0.156 10 false *b 1.219,0.427 1.531,0.583 0.313,0.156 10 false C47 1.958,0.427 2.271,0.583 0.313,0.156 10 false C66 2.292,1.729 2.802,1.885 0.51,0.156 10 false EGR *1 1.302,2.427 1.615,2.583 0.313,0.156 10 false C39 1.5,4.313 2.375,4.521 0.875,0.208 10 false 107 (EGRS) 2.5,4.313 3.375,4.521 0.875,0.208 10 false 108 (ERS2) 2.292,1.906 2.885,2.073 0.594,0.167 10 false EGR2 *2
*1 No. 1
*2 No. 2
*a Front view of wire harness connector
(to EGR Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the C47 or C66 EGR valve connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
No. 1
Tester Connection Condition Specified Condition
C47-5 (EGR) - C39-107 (EGRS) Always Below 1 Ω
C47-5 (EGR) or C39-107 (EGRS) - Body ground Always 10 kΩ or higher

No. 2
Tester Connection Condition Specified Condition
C66-5 (EGR2) - C39-108 (ERS2) Always Below 1 Ω
C66-5 (EGR2) or C39-108 (ERS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EGR VALVE POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EGR VALVE POWER SOURCE)
a.
A165766C03
1.052,1.115 1.49,1.396 0.438,0.281 1.896,1.115 2.333,1.396 0.438,0.281 1.24,2.208 0.948,2.615 true 0.177,0.146 0.448,0.365 0.271,0.219 10 false *a 0.813,2.635 1.063,2.833 0.25,0.198 10 false +B 1.5,0.958 1.688,1.135 0.188,0.177 10 false *1 2.365,0.969 2.552,1.146 0.188,0.177 10 false *2 1.156,1.177 1.469,1.354 0.313,0.177 10 false C47 1.99,1.177 2.302,1.354 0.313,0.177 10 false C66
*1 No. 1
*2 No. 2
*a Front view of wire harness connector
(to EGR Valve)


Disconnect the C47 or C66 EGR valve connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
No. 1
Tester Connection Switch Condition Specified Condition
C47-1 (+B) - Body ground Ignition switch ON 11 to 14 V

No. 2
Tester Connection Switch Condition Specified Condition
C66-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK FOR DEPOSIT (EGR VALVE [NO. 1 OR NO. 2])

NG

9.CHECK HARNESS AND CONNECTOR (NO. 1 EGR VALVE - MAIN RELAY, NO. 2 EGR VALVE - MAIN 2 RELAY)
6.CHECK FOR DEPOSIT (EGR VALVE [NO. 1 OR NO. 2])
a.

Check for any deposit.

OK:

No deposit.



Result:
Proceed to
OK
NG



OK

7.CHECK FOR DEPOSIT (EGR PASSAGE)

NG

REMOVE FOREIGN OBJECT AND CLEAN EGR VALVE (NO. 1 OR NO. 2)

7.CHECK FOR DEPOSIT (EGR PASSAGE)
a.

Check for any deposit.

OK:

No deposit.



Result:
Proceed to
OK
NG



OK

8.CHECK FOR EXHAUST GAS LEAKS

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.CHECK FOR EXHAUST GAS LEAKS
a.

Check for exhaust gas leaks.

OK:

No leaks.



Result:
Proceed to
OK
NG



OK

NG

REPAIR EXHAUST GAS LEAKAGE POINT

9.CHECK HARNESS AND CONNECTOR (NO. 1 EGR VALVE - MAIN RELAY, NO. 2 EGR VALVE - MAIN 2 RELAY)
a.

Disconnect the C47 or C66 EGR valve connector.


b.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
No. 1
Tester Connection Condition Specified Condition
C47-1 (+B) - MAIN relay terminal 3 Always Below 1 Ω
C47-1 (+B) or MAIN relay terminal 3 - Body ground Always 10 kΩ or higher

No. 2
Tester Connection Condition Specified Condition
C66-1 (+B) - MAIN 2 relay terminal 3 Always Below 1 Ω
C66-1 (+B) or MAIN 2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR