Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  P213B  Exhaust Gas Recirculation Throttle Position Control (Range / Performance)  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to opening and closing the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance When either condition below is met:
·

When throttle valve (for Bank 1) remains closed despite ECM's signal to open valve

(1 trip detection logic)

·

When throttle valve (for Bank 1) remains open despite ECM's signal to close valve

(1 trip detection logic)


·

Throttle valve (for Bank 1) stuck

·

Throttle valve (for Bank 1) does not move smoothly

·

Open or short in throttle valve (for Bank 1) circuit

·

ECM


Comes on DTC stored
P213B Exhaust Gas Recirculation Throttle Position Control (Range / Performance) When either condition below is met:
·

When throttle valve (for Bank 2) remains closed despite ECM's signal to open valve

(1 trip detection logic)

·

When throttle valve (for Bank 2) remains open despite ECM's signal to close valve

(1 trip detection logic)


·

Throttle valve (for Bank 2) stuck

·

Throttle valve (for Bank 2) does not move smoothly

·

Open or short in throttle valve (for Bank 2) circuit

·

ECM


Comes on DTC stored

Reference
Condition Throttle Valve Position
Moment when accelerator pedal is further depressed or released at 3000 rpm Opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and the ECM illuminates the MIL.

A128641E03
0.293,5.431 1.684,5.799 1.392,0.368 10 Duty Ratio Malfunction Counter 0.137,0.027 1.921,0.236 1.784,0.209 10 Malfunction Detection: 0.293,1.239 1.703,1.607 1.41,0.368 10 Throttle Valve Target Opening Angle 0.293,2.707 1.767,3.108 1.474,0.4 10 Throttle Valve Actual Opening Angle 0.949,4.117 1.685,4.333 0.736,0.216 10 Duty Ratio 4.797,1.709 5.39,1.91 0.593,0.201 10 Normal 4.797,2.475 5.547,2.676 0.751,0.201 10 Abnormal 4.797,3.98 5.39,4.182 0.593,0.201 10 Normal 4.797,3.215 5.547,3.416 0.751,0.201 10 Abnormal 5.95,0.557 6.401,0.758 0.45,0.201 10 Open 5.95,1.306 6.43,1.507 0.48,0.201 10 Close 5.95,2.017 6.401,2.219 0.45,0.201 10 Open 5.95,2.774 6.43,2.976 0.48,0.201 10 Close 5.95,3.516 6.465,3.72 0.514,0.204 10 100% 5.95,4.28 6.292,4.481 0.342,0.201 10 0% 3.368,5.26 4.789,5.467 1.421,0.208 10 Detect P0488, P213B 5.348,5.238 6.143,5.449 0.795,0.212 10 Threshold 3.509,6.268 3.92,6.471 0.411,0.204 10 Time 4.614,2.111 4.74,1.795 false 4.614,2.87 4.74,2.554 false 4.614,3.616 4.74,3.3 false 4.74,4.076 4.614,3.76 false 5.347,5.23 5.165,5.009 false 3.333,5.35 3.096,5.176 false

WIRING DIAGRAM

A165769E09
0.885,0.771 1.948,1.125 1.063,0.354 10 false from MAIN Relay Terminal 3 2.854,0.906 3.021,1.052 0.167,0.146 10 false 2 4.25,0.906 4.417,1.052 0.167,0.146 10 false 1 5.802,0.906 6.021,1.052 0.219,0.146 10 false 42 3.083,0.802 3.427,0.948 0.344,0.146 10 false VCR 3.74,0.802 4.177,0.948 0.438,0.146 10 false VTAR 6.135,0.802 6.594,0.948 0.458,0.146 10 false LUSL 5.823,3.458 6.042,3.604 0.219,0.146 10 false 84 6.135,3.344 6.594,3.49 0.458,0.146 10 false LUS2 4.25,1.594 4.417,1.74 0.167,0.146 10 false 3 3.844,1.5 4.146,1.646 0.302,0.146 10 false E2R 2.833,1.854 3.146,2.01 0.313,0.156 10 false C58 2.833,2.052 4.979,2.208 2.146,0.156 10 false Throttle Control Motor (for Bank 1) 2.875,3.458 3.042,3.604 0.167,0.146 10 false 2 4.26,3.469 4.427,3.615 0.167,0.146 10 false 1 3.083,3.354 3.427,3.5 0.344,0.146 10 false VCR 3.74,3.354 4.177,3.5 0.438,0.146 10 false VTAR 4.26,4.156 4.427,4.302 0.167,0.146 10 false 3 3.948,4.042 4.177,4.188 0.229,0.146 10 false E2 2.833,4.417 3.146,4.573 0.313,0.156 10 false C61 2.833,4.604 5.177,4.76 2.344,0.156 10 false Throttle Control Motor (for Bank 2) 6.292,5.25 6.594,5.438 0.302,0.188 10 false C39 6.292,5.396 6.729,5.583 0.438,0.188 10 false ECM 0.771,3.313 1.958,3.677 1.188,0.365 10 false from MAIN 2 Relay Terminal 3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

After warming up the engine, DTC P0488 and P213B can be set if 1 second or more passes after quickly accelerating the engine from idling.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0488, P213B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0488 and/or P213B are output A
P0488, P213B and P0122, P0123, P0222 and/or P0223 are output B


HINT:

If codes other than P0488, P213B are output, perform troubleshooting for those DTCs first.




A

2.CHECK IF DTC OUTPUT RECURS

B

2.CHECK IF DTC OUTPUT RECURS

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS ON.


d.

Start the engine and accelerate the engine from idle to 3000 rpm 3 times quickly.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0488 and/or P123B are output A
No DTC is output B


HINT:

The normal operation of the throttle valve is as follows.

Reference
Condition Throttle Valve Position
Moment when accelerator pedal is further depressed or released at 3000 rpm Opening angle varies smoothly




A

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)

B

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
A165767C02
1.021,1.208 1.458,1.5 0.438,0.292 1.896,1.208 2.354,1.531 0.458,0.323 2.104,2.271 2.563,2.385 true 1.74,2.375 1.74,2.854 true 0.229,0.188 0.542,0.406 0.313,0.219 10 false *a 1.531,1.125 1.708,1.302 0.177,0.177 10 false *1 1.573,2.906 1.938,3.083 0.365,0.177 10 false VCR 2.635,2.313 3.135,2.49 0.5,0.177 10 false E2R*1 2.635,2.563 3.146,2.74 0.51,0.177 10 false E2*2 2.427,1.135 2.604,1.313 0.177,0.177 10 false *2 1.135,1.281 1.427,1.458 0.292,0.177 10 false C58 2.021,1.292 2.313,1.469 0.292,0.177 10 false C61
*1 for Bank 1
*2 for Bank 2
*a Front view of wire harness connector
(to Throttle Control Motor)


Disconnect the C58 or C61 throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
for Bank 1
Tester Connection Switch Condition Specified Condition
C58-2 (VCR) - Body ground Ignition switch ON 11 to 14 V

for Bank 2
Tester Connection Switch Condition Specified Condition
C61-2 (VCR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - MAIN RELAY)
4.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.
A311468C02
1.125,0.26 1.552,0.542 0.427,0.281 1.844,0.26 2.271,0.542 0.427,0.281 1.26,2.417 1.688,2.698 0.427,0.281 0.927,1.625 1.344,1.208 true 2.313,1.635 1.979,1.219 true 1.354,4.313 2.063,3.313 true 2.271,4.333 2.26,3.552 true 1.552,0.094 1.865,0.25 0.313,0.156 10 false *1 2.281,0.104 2.594,0.26 0.313,0.156 10 false *2 0.229,0.125 0.542,0.281 0.313,0.156 10 false *a 0.188,2.063 0.5,2.219 0.313,0.156 10 false *b 1.229,0.323 1.542,0.479 0.313,0.156 10 false C58 1.948,0.323 2.26,0.479 0.313,0.156 10 false C61 1.365,2.479 1.677,2.635 0.313,0.156 10 false C39 0.74,1.646 1.229,1.833 0.49,0.188 10 false VTAR 2.25,1.667 2.74,1.854 0.49,0.188 10 false E2R*A 2.25,1.854 2.74,2.042 0.49,0.188 10 false E2*B 1.021,4.375 1.698,4.573 0.677,0.198 10 false 42 (LUSL) 1.99,4.385 2.667,4.583 0.677,0.198 10 false 84 (LUS2)
*1 for Bank 1
*2 for Bank 2
*a Front view of wire harness connector
(to Throttle Control Motor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C58 or C61 throttle control motor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
for Bank 1
Tester Connection Condition Specified Condition
C58-1 (VTAR) - C39-42 (LUSL) Always Below 1 Ω
C58-3 (E2R) - Body ground Always Below 1 Ω
C58-1 (VTAR) or C39-42 (LUSL) - Body ground Always 10 kΩ or higher

for Bank 2
Tester Connection Condition Specified Condition
C61-1 (VTAR) - C39-84 (LUS2) Always Below 1 Ω
C61-3 (E2) - Body ground Always Below 1 Ω
C61-1 (VTAR) or C39-84 (LUS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or for Bank 2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or for Bank 2)
a.

Replace the diesel throttle body assembly (for Bank 1 or for Bank 2).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the tester ON.


d.

Start the engine and drive the vehicle for approximately 15 minutes.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
P0488 and/or P213B are output A
P0488, P213B and P0122, P0123, P0222 and/or P0223 are output B




A

B

END

7.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - MAIN RELAY)
a.

Disconnect the C58 or C61 throttle control motor connector.


b.

Remove the MAIN or MAIN 2 relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
No. 1
Tester Connection Condition Specified Condition
C58-2 (VCR) - MAIN relay terminal 3 Always Below 1 Ω
C58-2 (VCR) or MAIN relay terminal 3 - Body ground Always 10 kΩ or higher

No. 2
Tester Connection Condition Specified Condition
C61-2 (VCR) - MAIN 2 relay terminal 3 Always Below 1 Ω
C61-2 (VCR) or MAIN 2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR