Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction One of the following conditions is met:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains ON and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

When the motor relay remains ON and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.12 seconds or more.

4.

With the IG1 terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.


·

ECU IG fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C304972E03
0.781,0.552 1.917,1.094 1.135,0.542 10 false from IG Circuit 2.708,0.719 3.271,1.021 0.563,0.302 10 false ECU IG 4.469,0.427 4.719,0.656 0.25,0.229 10 false 34 4.771,0.542 5.104,0.74 0.333,0.198 10 false IG1 4.76,1.49 5.229,1.688 0.469,0.198 10 false GND1 4.531,1.385 4.688,1.583 0.156,0.198 10 false 1 4.052,2.01 4.365,2.208 0.313,0.198 10 false A20 4.063,2.198 7.052,2.667 2.99,0.469 10 false Brake Actuator Assembly (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C260095C19
0.177,0.917 0.51,1.177 0.333,0.26 2.094,1.833 2.302,1.396 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 1.865,1.792 2.167,2 0.302,0.208 10 false IG1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the A20 brake actuator assembly (skid control ECU) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C260095C20
0.219,0.927 0.563,1.156 0.344,0.229 1.115,0.833 1.26,0.146 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.281,0.958 0.594,1.156 0.313,0.198 10 false A20 1.292,0.063 1.906,0.26 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 60 seconds or more.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.




DTC is not output

DTC is output