Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1418  Open or Short in Acceleration Sensor Circuit  


DESCRIPTION

The brake actuator assembly (skid control ECU) receives signals from the deceleration sensor. If the sensor functions abnormally, the ABS warning light turns on.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1243 Acceleration Sensor Stuck Malfunction The following condition repeats 16 times.
·

Sensor signal does not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).


·

Deceleration sensor

·

Harness or connector

·

Brake actuator assembly (Skid control ECU)


C1245 Acceleration Sensor Output Malfunction The following condition continues for at least 60 seconds.
·

The difference between the values calculated from the deceleration sensor value and vehicle speed exceeds 0.35 G.


·

Deceleration sensor

·

Harness or connector

·

Brake actuator assembly (Skid control ECU)


C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC) Stored during test mode.
·

Deceleration sensor

·

Harness or connector

·

Brake actuator assembly (Skid control ECU)


C1418 Open or Short in Acceleration Sensor Circuit One of the following conditions is met when the voltage at terminal IG1 is 9.5 V or higher:
·

The VGS output value of the deceleration sensor is outside the range of 4.4 to 5.6 V for 1.2 seconds or more.

·

The value of GL1 is outside the range of -1.5 to 1.5 G for 1.2 seconds or more.

·

A deceleration sensor open circuit occurs 7 times or more.


·

Deceleration sensor

·

Harness or connector

·

Brake actuator assembly (Skid control ECU)



WIRING DIAGRAM

C177519E06
0.885,1.417 1.354,1.635 0.469,0.219 10 false GGND 1.021,1.031 1.396,1.271 0.375,0.24 10 false GL1 0.99,0.635 1.438,0.865 0.448,0.229 10 false VGS 5.927,1.396 6.583,1.635 0.656,0.24 10 false GGND 5.927,1.01 6.417,1.219 0.49,0.208 10 false GL1 5.927,0.615 6.375,0.875 0.448,0.26 10 false VGS 0.552,1.927 0.844,2.094 0.292,0.167 10 false I9 0.552,2.094 1.906,2.323 1.354,0.229 10 false Deceleration Sensor 1.427,1.25 1.583,1.406 0.156,0.156 10 false 2 1.427,0.854 1.583,1.01 0.156,0.156 10 false 1 1.427,0.469 1.583,0.625 0.156,0.156 10 false 3 5.646,1.24 5.854,1.406 0.208,0.167 10 false 15 5.708,0.865 5.917,1.031 0.208,0.167 10 false 3 5.646,0.458 5.854,0.625 0.208,0.167 10 false 26 5.448,1.76 5.792,1.917 0.344,0.156 10 false A20 5.448,1.958 7.073,2.406 1.625,0.448 10 false Brake Actuator Assembly (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK DECELERATION SENSOR INSTALLATION
a.

Check that the deceleration sensor is installed properly.

Result:
Result Proceed to
The sensor is tightened to the specified torque.
The sensor is not tilted.
A
The sensor is not tightened to the specified torque, or the sensor is tilted. B




A

2.READ VALUE USING GTS (DECELERATION SENSOR)

B

2.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor Deceleration sensor reading Min.: -18.525 m/s2
Max.: 18.387 m/s2
- Changes continuously during acceleration/deceleration.
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
50003 105 14

f.

Check the Data List for proper functioning of the deceleration sensor.

OK:

Deceleration value changes.



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

4.INSPECT DECELERATION SENSOR
3.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds or more.


d.

Check if the same DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

DTC is output

4.INSPECT DECELERATION SENSOR


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DECELERATION SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DECELERATION SENSOR)
a.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A20-3 (GL1) - I9-1 (GL1) Always Below 1 Ω
A20-15 (GGND) - I9-2 (GGND) Always Below 1 Ω
A20-26 (VGS) - I9-3 (VGS) Always Below 1 Ω
A20-3 (GL1) or I9-1 (GL1) - Body ground Always 10 kΩ or higher
A20-15 (GGND) or I9-2 (GGND) - Body ground Always 10 kΩ or higher
A20-26 (VGS) or I9-3 (VGS) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DTC

b.

Connect the brake actuator assembly (skid control ECU) connector.


c.

Connect the deceleration sensor connector.


d.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

e.

Turn the ignition switch off.


f.

Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds or more.


g.

Check if the same DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

DTC is output