Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1282  Center Differential Lock Position Switch  


DESCRIPTION

DTC C1282 is output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1282 Center Differential Lock Position Switch Detected only during Test Mode.
·

Transfer system

·

No. 1 transfer indicator switch (4WD position switch)

·

EXI terminal circuit

·

Brake actuator assembly (Skid control ECU)



WIRING DIAGRAM

C275420E02
0.125,1.875 0.49,2.073 0.365,0.198 10 false L25 0.125,2.052 2.01,2.25 1.885,0.198 10 false Combination Meter Assembly 0.365,1.042 0.76,1.24 0.396,0.198 10 false 4WD 0.531,0.323 0.802,0.5 0.271,0.177 10 false IG 6.188,0.156 6.458,0.333 0.271,0.177 10 false IG 5.302,1.792 5.844,1.979 0.542,0.188 10 false A20 5.302,1.99 6.917,2.375 1.615,0.385 10 false Brake Actuator Assembly (Skid Control ECU) 5.104,0.74 5.354,0.927 0.25,0.188 10 false 31 5.406,0.74 5.729,0.938 0.323,0.198 10 false EXI 1.688,0.75 1.865,0.938 0.177,0.188 10 false 2 3.25,3.427 4.229,3.604 0.979,0.177 10 false C35*1, C98*2 3.25,3.656 6.938,3.927 3.688,0.271 10 false No. 1 Transfer Indicator Switch (4WD Position Switch) 3.667,2.865 3.854,3.083 0.188,0.219 10 false 2 4.958,2.865 5.135,3.073 0.177,0.208 10 false 1 0.188,3.896 2.135,4.094 1.948,0.198 10 false *1: for 1VD-FTV and 1GR-FE 0.188,4.219 2.135,4.417 1.948,0.198 10 false *2: for 1HZ 4.521,3.156 4.979,3.354 0.458,0.198 10 false GND 3.896,3.167 4.052,3.365 0.156,0.198 10 false B 1.354,0.719 1.667,0.917 0.313,0.198 10 false SW

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EXI TERMINAL)
a.

Set the vehicle to the 4WD state.


b.
C260095C21
0.25,0.917 0.583,1.208 0.333,0.292 2.177,1.969 1.969,1.969 1.969,1.969 1.969,1.396 true 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 0.302,0.99 0.635,1.188 0.333,0.198 10 false A20 2.198,1.885 2.656,2.083 0.458,0.198 10 false EXI
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-31 (EXI) - Body ground
·

Ignition switch ON

·

Transfer position 4WD


Below 1.5 V



e.

Turn the ignition switch off.


f.

Connect the brake actuator assembly (skid control ECU) connector.


g.

Set the vehicle to the 2WD state.


h.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


i.

Turn the ignition switch to ON.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-31 (EXI) - Body ground
·

Ignition switch ON

·

Transfer position 2WD


11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TEST MODE DTC

NG

3.CHECK HARNESS AND CONNECTOR (EXI CIRCUIT)
2.CHECK TEST MODE DTC
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.

Switch the vehicle to Test Mode, perform the 2WD to 4WD shift operation check, and then check that DTC C1282 is not stored.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

Result:
Proceed to
DTC is stored
DTC is not stored



DTC is stored

DTC is not stored

3.CHECK HARNESS AND CONNECTOR (EXI CIRCUIT)
a.

Turn the ignition switch off.


b.

for 1VD-FTV and 1GR-FE:

Disconnect the C35 No. 1 transfer indicator switch (4WD position switch) connector.


c.

for 1HZ:

Disconnect the C98 No. 1 transfer indicator switch (4WD position switch) connector.


d.

Disconnect the L25 combination meter assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1VD-FTV and 1GR-FE
Tester Connection Condition Specified Condition
A20-31 (EXI) - C35-2 (B) Always Below 1 Ω
A20-31 (EXI) - L25-2 (SW) Always Below 1 Ω
A20-31 (EXI) - Body ground Always 10 kΩ or higher
C35-2 (B) - Body ground Always 10 kΩ or higher
L25-2 (SW) - Body ground Always 10 kΩ or higher
C35-1 (GND) - Body ground Always Below 1 Ω

for 1HZ
Tester Connection Condition Specified Condition
A20-31 (EXI) - C98-2 (B) Always Below 1 Ω
A20-31 (EXI) - L25-2 (SW) Always Below 1 Ω
A20-31 (EXI) - Body ground Always 10 kΩ or higher
C98-2 (B) - Body ground Always 10 kΩ or higher
L25-2 (SW) - Body ground Always 10 kΩ or higher
C98-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 1 TRANSFER INDICATOR SWITCH (4WD POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 1 TRANSFER INDICATOR SWITCH (4WD POSITION SWITCH)
a.

Remove the No. 1 transfer indicator switch (4WD position switch).



b.

Inspect the No. 1 transfer indicator switch (4WD position switch).



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 TRANSFER INDICATOR SWITCH (4WD POSITION SWITCH)