Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1403  Rear Speed Sensor RH Malfunction  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). These signals are used for brake control.

The speed sensor detects changes in the magnetic field emitted from the speed sensor rotor and generates a vehicle speed pulse. The brake actuator assembly (skid control ECU) detects the speed of each wheel using this vehicle speed pulse.

HINT:

When the connectors between the speed sensor and brake actuator assembly (skid control ECU) are connected, the following waveform is output.


C271026E02
1.083,0.5 1.25,0.5 1.25,0.5 1.333,1 false 6.042,1.729 5.302,1.729 5.302,1.729 5.302,1.448 false 6.031,2.073 4.24,2.073 4.24,2.073 4.24,1.448 false 0.198,0.448 1.271,0.646 1.073,0.198 10 false Speed Sensor 1.042,2.167 1.958,2.365 0.917,0.198 10 false Speed Sensor Rotor 6.094,0.75 6.865,0.948 0.771,0.198 10 false 1.4 V 6.104,1.135 6.875,1.333 0.771,0.198 10 false 0.7 V 6.094,1.99 6.854,2.177 0.76,0.188 10 false Low speed 6.083,1.635 6.854,1.875 0.771,0.24 10 false High speed 2.896,0.167 7.052,0.458 4.156,0.292 10 false Waveform (Reference): Between Speed Sensor (-) and Body Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Stored only during test mode.
·

Rear speed sensor RH

·

Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)

·

Rear speed sensor RH installation


C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Stored only during test mode.
·

Rear speed sensor LH

·

Rear axle hub and bearing assembly LH (Rear speed sensor rotor LH)

·

Rear speed sensor LH installation


C1403 Rear Speed Sensor RH Malfunction One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed less than 10 km/h (6 mph), outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Rear speed sensor RH

·

Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)

·

Rear speed sensor RH installation


C1404 Rear Speed Sensor LH Malfunction One of the following conditions is met:
1.

At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed less than 10 km/h (6 mph), outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Rear speed sensor LH

·

Rear axle hub and bearing assembly LH (Rear speed sensor rotor LH)

·

Rear speed sensor LH installation



HINT:
·

DTCs C1403 and C1273 are for the rear speed sensor RH.

·

DTCs C1404 and C1274 are for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C144929C11
1.156,2.771 0.979,2.771 0.979,2.771 0.698,2.49 false 0.083,0.083 0.396,0.24 0.313,0.156 10 false *1 1.198,2.708 1.51,2.865 0.313,0.156 10 false *a 0.615,2.896 0.927,3.052 0.313,0.156 10 false *b 2.698,2.948 3.01,3.104 0.313,0.156 10 false *c
*1 Rear Speed Sensor
*a No Clearance
*b OK
*c NG


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(w/ ABS)>INSTALLATION

OK:

There is no clearance between the sensor and the rear axle.

The installation nut is tightened properly.



Result:
Proceed to
OK
NG



OK

2.INSPECT REAR SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

2.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.INSPECT REAR SPEED SENSOR ROTOR
a.

Remove the rear axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (RR/RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR ROTOR

4.READ VALUE USING GTS (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Install the rear axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION



d.

Connect the GTS to the DLC3.


e.

Start the engine.


f.

Turn the GTS on.


g.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

h.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error.

This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR
a.

Replace the rear speed sensor.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

END

DTC is output

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY