Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1427  Motor Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1427 Motor Malfunction The actuator pump motor does not operate properly.
·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON / OFF The operating sound of the motor can be heard.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2

f.

Check for the operating sound of the ABS motor relay when operating it with the GTS.

Result:
Proceed to
Operating sound is not heard
Operating sound is heard




Operating sound is not heard

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

Operating sound is heard

3.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.
C260095C23
0.177,0.917 0.51,1.177 0.333,0.26 0.615,1.844 0.615,1.74 0.615,1.74 1.042,1.302 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 0.438,1.844 0.865,2.052 0.427,0.208 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The ABS motor relay is in the brake actuator assembly.

Therefore, ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Connect the brake actuator assembly (skid control ECU) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the brake actuator assembly (skid control ECU) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





DTC is not output

DTC is output