Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.

If the voltage supplied to the motor relay (+BM) is below the DTC's detection threshold due to low voltage from the battery or generator, the DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146C Open in ABS Motor Relay Circuit When either of the following is detected:
1.

All of the following conditions continue for 0.12 seconds or more.

-

The IG1 terminal voltage is between 9.5 and 17.2 V.

-

While initial check and ABS is operating.

-

Relay contact is open when the relay is ON.


2.

Both of the following conditions continue for 0.12 seconds.

-

The IG1 terminal voltage is less than 9.5 V.

-

Relay contact remains open when the relay is ON.



·

ABS MTR fuse

·

ABS motor relay circuit

·

Brake actuator assembly (ABS motor relay)


C146D Short in ABS Motor Relay Circuit When the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
·

ABS motor relay circuit

·

Brake actuator assembly (ABS motor relay)



WIRING DIAGRAM

C268624E04
0.75,1.396 1.542,1.573 0.792,0.177 10 false from Battery 1.938,1.583 2.719,1.74 0.781,0.156 10 false ABS MTR 3.5,1.313 3.677,1.469 0.177,0.156 10 false 24 3.5,3.281 3.677,3.438 0.177,0.156 10 false 13 3.75,1.5 4.521,1.656 0.771,0.156 10 false +BM 3.75,3.469 4.385,3.625 0.635,0.156 10 false GND2 4.865,0.604 6.031,0.76 1.167,0.156 10 false Skid Control ECU 5,1.323 5.833,1.51 0.833,0.188 10 false Motor Relay 5.146,4.729 5.979,4.917 0.833,0.188 10 false Pump Motor 3.771,5.156 4.24,5.313 0.469,0.156 10 false A20 3.771,5.313 5.458,5.469 1.688,0.156 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



HINT:

When C1241 is output together with C146C and/or C146D, inspect and repair the trouble areas indicated by C1241 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON / OFF The operating sound of the motor can be heard.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2

f.

Check the operating sound of the ABS motor relay when operating it with the GTS.

Result:
Proceed to
The operating sound is not heard
The operating sound is heard




The operating sound is not heard

2.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)

The operating sound is heard

4.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


b.
C260095C24
0.177,0.917 0.51,1.177 0.333,0.26 2.177,1.875 2.458,1.323 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 1.844,1.823 2.188,2.031 0.344,0.208 10 false +BM
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-24 (+BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C260095C23
0.177,0.917 0.51,1.177 0.333,0.26 0.615,1.844 0.615,1.74 0.615,1.74 1.042,1.302 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 0.438,1.844 0.865,2.052 0.427,0.208 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

4.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The ABS motor relay is in the brake actuator assembly.

Therefore, ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Connect the brake actuator assembly (skid control ECU) connector.


b.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the brake actuator assembly (skid control ECU), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





DTC is not output

DTC is output