Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136556 CYLINDER HEAD GASKET A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

Hide 11116 3.INSTALL NO. 2 CYLINDER HEAD GASKET

a.

Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head LH and cylinder block.


b.
A326582C01
2.083,1.313 2.25,1.063 2.25,1.063 2.417,1.063 false 1.948,1.49 2.198,1.49 false 1.479,1.125 1.646,1.125 false 2.469,0.979 2.781,1.135 0.313,0.156 10 false *1 0,0.375 0.313,0.531 0.313,0.156 10 false *a 0.448,0.875 0.76,1.031 0.313,0.156 10 false *b 1.583,1.802 1.896,1.958 0.313,0.156 10 false *c 1.323,1.042 1.635,1.198 0.313,0.156 10 false *d 0,2.333 0.313,2.49 0.313,0.156 10 false *a 0.438,2.823 0.75,2.979 0.313,0.156 10 false *b 2.24,1.396 2.552,1.552 0.313,0.156 10 false *d
*1 No. 2 Cylinder Head Gasket
*a Seal Packing Application Range
*b 10 to 15 mm (0.394 to 0.591 in.)
*c 1.25 to 1.5 mm (0.0492 to 0.0591 in.)
*d Seal Packing


Apply seal packing to a new No. 2 cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.0 mm (0.0984 to 0.118 in.)


NOTICE:
·

Install the No. 2 cylinder head gasket within 3 minutes after applying the seal packing.

·

Do not add engine oil within 2 hours of installation.




c.
A326583C01
1.719,1.969 1.927,1.969 1.927,1.969 1.927,1.625 true 1.552,1.875 1.865,2.031 0.313,0.156 10 false *a
*a Lot No. Stamp


Place the No. 2 cylinder head gasket on the cylinder block sub-assembly surface with the front face of the Lot No. stamp upward.

NOTICE:

Pay attention to the installation direction.



Hide 11102 4.INSTALL CYLINDER HEAD LH

a.

Clean and remove any oil from the cylinder head installation surface.


b.

Place the cylinder head LH on the No. 2 cylinder head gasket.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head LH.

·

Do not damage the cylinder head LH and No. 2 cylinder head gasket.




c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


d.

Install the 8 cylinder head set bolts and 8 plate washers.

NOTICE:
·

Install the cylinder head set bolts to their original positions.

·

Do not drop the plate washer for the cylinder head set bolt into the cylinder head LH.

·

The cylinder head set bolts are tightened in 2 progressive steps.

·

If any cylinder head set bolt is broken or deformed, replace it.




e.

Step 1:

i.
A326580N02
0.792,0.24 0.938,0.427 0.146,0.188 10 true 8 1.458,0.26 1.604,0.448 0.146,0.188 10 true 1 2.188,0.271 2.333,0.458 0.146,0.188 10 true 3 2.823,0.302 2.969,0.49 0.146,0.188 10 true 5 2.844,1.906 2.99,2.094 0.146,0.188 10 true 7 2.208,1.906 2.354,2.094 0.146,0.188 10 true 2 1.5,1.896 1.646,2.083 0.146,0.188 10 true 4 0.813,1.896 0.958,2.083 0.146,0.188 10 true 6

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head set bolts with plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

If any one of the cylinder head set bolts does not meet the torque specification, replace the cylinder head set bolt.



f.

Step 2:

i.

Mark the engine front side of each cylinder head set bolt head with paint.


ii.

Tighten the cylinder head set bolts 180° in the sequence shown in step 1.



g.

Check that the painted marks are now facing rearward.


h.

Apply a light coat of engine oil to the threads of the bolts.


i.
A326579N02
0.125,0.677 0.281,0.875 0.156,0.198 10 false 1 0.135,1.469 0.292,1.667 0.156,0.198 10 false 2

Install the 2 bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


j.
A327365C01
2.302,1.292 2.302,0.99 2.302,0.99 2.448,0.99 false 0.917,1.281 0.917,1.281 0.917,1.281 1.25,1.281 false 2.021,0.396 2.333,0.552 0.313,0.156 10 false *1 2.5,0.927 2.813,1.083 0.313,0.156 10 false *2 2,1.604 2.313,1.76 0.313,0.156 10 false *3 0.063,0.083 0.375,0.24 0.313,0.156 10 false *a 0.74,1.208 1.052,1.365 0.313,0.156 10 false *b
*1 Cylinder Head LH
*2 No. 2 Cylinder Head Gasket
*3 Cylinder Block Sub-assembly
*a Engine Front Side
*b Wipe Clean


Seal packing will seep out from the front side of the engine. Thoroughly wipe off the seal packing that seeps out.


Hide 11115 5.INSTALL CYLINDER HEAD GASKET

a.

Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


b.
A326584C01
2.365,1.594 2.583,1.313 2.583,1.313 2.76,1.313 false 1.781,1.427 1.958,1.427 false 2.271,1.76 2.448,1.76 false 2.833,1.24 3.146,1.396 0.313,0.156 10 false *1 0.198,0.563 0.51,0.719 0.313,0.156 10 false *a 0.667,0.094 0.979,0.25 0.313,0.156 10 false *b 1.917,2.063 2.229,2.219 0.313,0.156 10 false *c 1.625,1.344 1.938,1.5 0.313,0.156 10 false *d 0.198,2.698 0.51,2.854 0.313,0.156 10 false *a 0.719,3.198 1.031,3.354 0.313,0.156 10 false *b 2.5,1.677 2.813,1.833 0.313,0.156 10 false *d
*1 Cylinder Head Gasket
*a Seal Packing Application Range
*b 10 to 15 mm (0.394 to 0.591 in.)
*c 1.25 to 1.5 mm (0.0492 to 0.0591 in.)
*d Seal Packing


Apply seal packing to a new cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.0 mm (0.0984 to 0.118 in.)


NOTICE:
·

Install the cylinder head gasket within 3 minutes after applying the seal packing.

·

Do not add engine oil within 2 hours of installation.




c.
A326585C01
1.385,0.177 1.604,0.177 1.604,0.177 1.729,0.458 true 1.219,0.115 1.531,0.271 0.313,0.156 10 false *a
*a Lot No. Stamp


Place the cylinder head gasket on the cylinder block sub-assembly surface with the front face of the Lot No. stamp upward.

NOTICE:

Pay attention to the installation direction.



Hide 11101 6.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Clean and remove any oil from the cylinder head installation surface.


b.

Place the cylinder head sub-assembly on the cylinder head gasket.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Do not damage the cylinder head sub-assembly and cylinder head gasket.




c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


d.

Install the 8 cylinder head set bolts and 8 plate washers.

NOTICE:
·

Install the cylinder head set bolts to their original positions.

·

Do not drop the plate washer for the cylinder head set bolt into the cylinder head sub-assembly.

·

The cylinder head set bolts are tightened in 2 progressive steps.

·

If any cylinder head set bolt is broken or deformed, replace it.




e.

Step 1:

i.
A326577N02
0.635,0.073 0.813,0.25 0.177,0.177 10 true 6 1.333,0.063 1.51,0.24 0.177,0.177 10 true 4 2.042,0.073 2.219,0.25 0.177,0.177 10 true 2 2.719,0.063 2.896,0.24 0.177,0.177 10 true 7 0.698,1.677 0.875,1.854 0.177,0.177 10 true 8 1.365,1.677 1.542,1.854 0.177,0.177 10 true 1 2.042,1.677 2.219,1.854 0.177,0.177 10 true 3 2.719,1.688 2.896,1.865 0.177,0.177 10 true 5

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head set bolts with plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

If any one of the cylinder head set bolts does not meet the torque specification, replace the cylinder head set bolt.



f.

Step 2:

i.

Mark the engine front side of each cylinder head set bolt head with paint.


ii.

Tighten the cylinder head set bolts 180° in the sequence shown in step 1.



g.

Check that the painted marks are now facing rearward.


h.
A327365C01
2.302,1.292 2.302,0.99 2.302,0.99 2.448,0.99 false 0.917,1.281 0.917,1.281 0.917,1.281 1.25,1.281 false 2.021,0.396 2.333,0.552 0.313,0.156 10 false *1 2.5,0.927 2.813,1.083 0.313,0.156 10 false *2 2,1.604 2.313,1.76 0.313,0.156 10 false *3 0.063,0.083 0.375,0.24 0.313,0.156 10 false *a 0.74,1.208 1.052,1.365 0.313,0.156 10 false *b
*1 Cylinder Head Sub-assembly
*2 Cylinder Head Gasket
*3 Cylinder Block Sub-assembly
*a Engine Front Side
*b Wipe Clean


Seal packing will seep out from the front side of engine. Thoroughly wipe off the seal packing that seeps out.


Hide 13054 7.INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 13053 8.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 9.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

Hide 11821 10.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 11.INSTALL NO. 1 CAMSHAFT BEARING

Hide 14.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

Hide 13560A 15.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 16.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

Hide 13550 17.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 18.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

Hide 13561 19.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 20.INSTALL CRANKSHAFT TIMING SPROCKET

Hide 13559 21.INSTALL CHAIN TENSIONER SLIPPER

Hide 13540 22.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 23.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13506 24.INSTALL CHAIN SUB-ASSEMBLY

Hide 13562 25.INSTALL NO. 2 CHAIN VIBRATION DAMPER

Hide 13530 26.INSTALL IDLE SPROCKET ASSEMBLY

Hide 11302 27.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY