Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136556 CYLINDER HEAD GASKET A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 2.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13540 3.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 4.REMOVE CHAIN TENSIONER SLIPPER

Hide 13530 5.REMOVE IDLE SPROCKET ASSEMBLY

Hide 13562 6.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13521 8.REMOVE CRANKSHAFT TIMING SPROCKET

Hide 13561 9.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 10.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

Hide 13550 11.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 12.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

Hide 13560A 13.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 14.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

Hide 11811 17.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 18.REMOVE NO. 2 CAMSHAFT BEARING

Hide 19.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

Hide 13053 20.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 13054 21.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 11101 22.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A326577N01
0.635,0.073 0.813,0.25 0.177,0.177 10 true 3 1.333,0.063 1.51,0.24 0.177,0.177 10 true 5 2.042,0.073 2.219,0.25 0.177,0.177 10 true 7 2.719,0.063 2.896,0.24 0.177,0.177 10 true 2 0.698,1.677 0.875,1.854 0.177,0.177 10 true 1 1.365,1.677 1.542,1.854 0.177,0.177 10 true 8 2.042,1.677 2.219,1.854 0.177,0.177 10 true 6 2.719,1.688 2.896,1.865 0.177,0.177 10 true 4

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head set bolts in the sequence shown in the illustration and remove the 8 cylinder head set bolts and 8 plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly.

·

Cylinder head sub-assembly warpage or cracking could result from removing bolts in the incorrect order.



HINT:

Be sure to keep the removed parts separate for each installation position.



b.
A326578C01
1.823,1.24 2.313,1.24 true 2.354,1.135 2.573,1.344 0.219,0.208 10 true *a
*a Protective Tape


Remove the cylinder head sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


HINT:
·

If the cylinder head sub-assembly is difficult to lift off, pry between the cylinder head sub-assembly and cylinder block sub-assembly with a screwdriver.

·

Tape the screwdriver tip before use.




Hide 11115 23.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket.


Hide 11102 24.REMOVE CYLINDER HEAD LH

a.
A326579N01
0.125,0.677 0.281,0.875 0.156,0.198 10 false 2 0.135,1.469 0.292,1.667 0.156,0.198 10 false 1

Uniformly loosen the 2 bolts in the sequence shown in the illustration and remove the 2 bolts.


b.
A326580N01
0.792,0.24 0.938,0.427 0.146,0.188 10 true 1 1.458,0.26 1.604,0.448 0.146,0.188 10 true 8 2.188,0.271 2.333,0.458 0.146,0.188 10 true 6 2.823,0.302 2.969,0.49 0.146,0.188 10 true 4 2.844,1.906 2.99,2.094 0.146,0.188 10 true 2 2.208,1.906 2.354,2.094 0.146,0.188 10 true 7 1.5,1.896 1.646,2.083 0.146,0.188 10 true 5 0.813,1.896 0.958,2.083 0.146,0.188 10 true 3

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head set bolts in the sequence shown in the illustration and remove the 8 cylinder head set bolts and 8 plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head LH.

·

Cylinder head LH warpage or cracking could result from removing bolts in the incorrect order.



HINT:

Be sure to keep the removed parts separate for each installation position.



c.
A326581C01
1.292,1.281 0.979,1.688 0.979,1.688 0.792,1.688 true 0.615,1.604 0.927,1.76 0.313,0.156 10 false *a
*a Protective Tape


Remove the cylinder head LH.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head LH and cylinder block sub-assembly.


HINT:
·

If the cylinder head LH is difficult to lift off, pry between the cylinder head LH and cylinder block sub-assembly with a screwdriver.

·

Tape the screwdriver tip before use.




Hide 11116 25.REMOVE NO. 2 CYLINDER HEAD GASKET

a.

Remove the No. 2 cylinder head gasket.