Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136560 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 83520 1.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY (w/ Oil Pressure Gauge)

Hide 83530 2.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY (w/o Oil Pressure Gauge)

Hide 89422 3.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11415 4.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A286407

Remove the cylinder block water drain cock sub-assembly.


Hide 15330B 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

Hide 15330B 9.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 15678A 10.REMOVE OIL CONTROL VALVE FILTER

a.
A326603C01
0.083,0.188 0.396,0.344 0.313,0.156 10 false *a 1.635,0.146 1.948,0.302 0.313,0.156 10 false *b
*a RH Side
*b LH Side


Remove the 2 unions, 2 oil control valve filters and 2 gaskets.


Hide 15601 11.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15778 12.REMOVE NO. 2 OIL COOLER HOSE

Hide 15710 14.REMOVE OIL COOLER ASSEMBLY

Hide 15609 15.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A151244

Remove the 3 bolts, 2 nuts, oil filter bracket sub-assembly and O-ring.


Hide 16261 16.REMOVE NO. 1 WATER BY-PASS HOSE

a.

Slide the 2 hose clamps and remove the No. 1 water by-pass hose.


Hide 16264 17.REMOVE NO. 2 WATER BY-PASS HOSE

a.

Slide the 2 hose clamps and remove the No. 2 water by-pass hose.


Hide 16267 18.REMOVE NO. 3 WATER BY-PASS HOSE

a.

Slide the 2 hose clamps and remove the No. 3 water by-pass hose.


Hide 16323 19.REMOVE WATER INLET HOUSING

a.
A218524

Remove the 5 bolts, water inlet housing, O-ring and gasket.


Hide 16356 20.REMOVE REAR WATER BY-PASS JOINT

Hide 12108 21.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A218526

Remove the oil filler cap sub-assembly.


Hide 12185 22.REMOVE OIL FILLER CAP HOUSING

a.

Remove the 2 nuts, oil filler cap housing and gasket.


Hide 11201 24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A218527

Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover sub-assembly and gasket.


Hide 12204 25.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 11202 26.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A218528

Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover sub-assembly LH and gasket.


Hide 27.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13471 28.REMOVE CRANKSHAFT PULLEY

a.
A326605N01
0.667,1.083 1.073,1.083 false 2.021,0.823 2.292,1.573 2.292,1.573 2.51,1.573 true 0.375,1 0.833,1.198 0.458,0.198 10 false SST 2.563,1.49 3.021,1.688 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Screw the crankshaft pulley set bolt into the crankshaft by 2 or 3 threads.


c.
A326606C01
2.01,0.198 2.208,0.198 2.208,0.198 2.208,0.75 true 1.26,1.156 1.49,1.156 false 0.958,1.083 1.417,1.281 0.458,0.198 10 false SST 1.833,0.135 2.292,0.333 0.458,0.198 10 false *1 0.083,2.094 0.542,2.292 0.458,0.198 10 false *a 2.365,3.146 2.823,3.344 0.458,0.198 10 false *b
*1 Crankshaft Pulley Set Bolt
*a Hold
*b Turn


Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)


Hide 12101A 29.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket.


Hide 12102A 30.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A218529

Remove the 10 bolts and 2 nuts.


b.
A218530C01
0.865,1.063 0.635,1.667 0.635,1.667 0.635,1.75 true 0.563,1.781 0.813,1.938 0.25,0.156 10 false *a
*a Oil Pan Seal Cutter


Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.



Hide 15104 31.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A286383

Remove the 2 nuts, oil strainer sub-assembly and gasket.


Hide 12101 32.REMOVE OIL PAN SUB-ASSEMBLY

a.
A222082

Remove the 17 bolts and 2 nuts.


b.
A327366C01
2.448,0.823 2.698,0.406 2.698,0.406 2.865,0.406 true 0.438,1.771 0.75,1.927 0.313,0.156 10 false *a 0.427,3.323 0.74,3.479 0.313,0.156 10 false *b 2.906,0.323 3.219,0.479 0.313,0.156 10 false *c 2.531,1.177 2.844,1.333 0.313,0.156 10 false *d
*a LH Side
*b RH Side
*c Protective Tape
*d Pry


Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A326607

Remove the O-ring from the timing chain cover sub-assembly.


Hide 11381 33.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A326608C01
0.344,1.146 0.344,0.927 0.344,0.927 0.615,0.635 true 0.781,0.26 0.99,0.448 0.208,0.188 10 true *a 0.292,1.188 0.5,1.375 0.208,0.188 10 true *b
*a Pry
*b Protective Tape


Remove the 5 bolts and 2 nuts.


b.

Using a screwdriver, remove the engine rear oil seal retainer by prying between the engine rear oil seal retainer and crankshaft bearing cap.

HINT:

Tape the screwdriver tip before use.



Hide 11381A 34.REMOVE ENGINE REAR OIL SEAL

a.
A326609

Using a screwdriver and hammer, tap out the engine rear oil seal.

NOTICE:

Be careful not to damage the engine rear oil seal retainer.



Hide 11302 35.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A327367C01
1.292,0.969 1.448,1.167 0.156,0.198 10 false .
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Remove the 24 bolts and 2 nuts.


b.
A326610C01
1.323,0.156 1.5,0.156 1.5,0.156 1.948,0.646 true 1.917,3.167 2.115,3.167 2.115,3.167 2.583,2.781 true 0.719,1.885 0.542,1.885 0.542,1.885 0.542,2.615 true 2.583,1.333 3.115,1.333 true 1.146,0.073 1.458,0.271 0.313,0.198 10 false *a 1.75,3.083 2.063,3.281 0.313,0.198 10 false *a 0.771,1.792 1.083,1.99 0.313,0.198 10 false *a 3.146,1.25 3.375,1.448 0.229,0.198 10 false *a
*a Protective Tape


Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

NOTICE:

Do not damage the surrounding parts.


HINT:

Tape the screwdriver tip before use.



c.

Remove the O-ring from the cylinder head LH.


Hide 16100 36.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A179596

Remove the 8 bolts, engine water pump assembly and gasket.


Hide 11324 37.REMOVE TIMING CHAIN COVER PLATE

Hide 13540 39.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

Never rotate the crankshaft with the No. 1 chain tensioner assembly removed.

·

When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from TDC first.



a.
A158627C01
0.906,1.26 0.906,1.771 false 2.531,1.281 2.531,1.802 false 0.833,1.792 1.042,1.979 0.208,0.188 10 false *b 2.448,1.833 2.677,2.031 0.229,0.198 10 false *b 1.469,0.771 1.667,0.958 0.198,0.188 10 true *a
*a Push
*b Stopper Plate


While turning the stopper plate of the No. 1 chain tensioner assembly clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.


b.

While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a bar with a diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.


c.

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 40.REMOVE CHAIN TENSIONER SLIPPER

a.

Remove the chain tensioner slipper.


Hide 13530 41.REMOVE IDLE SPROCKET ASSEMBLY

a.
A326611

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


Hide 13562 42.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A326612

Remove the 2 No. 2 chain vibration dampers.


Hide 13506 43.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13521 44.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A326613

Remove the crankshaft timing sprocket.


Hide 13561 45.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A326614

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 46.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

a.
A316657C01
2.135,1.156 2.365,1.344 0.229,0.188 10 true *a
*a Raise


While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 2 chain tensioner assembly in place.


b.
A326615

Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the 2 bolts, camshaft timing gear sub-assembly, camshaft timing sprocket and No. 2 chain sub-assembly.

NOTICE:
·

Do not damage the surrounding parts.

·

Do not disassemble the camshaft timing gear sub-assembly.




Hide 13550 47.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A326616

Remove the bolt and No. 2 chain tensioner assembly.


Hide 48.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

a.
A316671C01
1.99,0.177 2.302,0.333 0.313,0.156 10 false *a
*a Push


While raising the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 3 chain tensioner assembly in place.


b.
A218533

Hold the hexagonal portion of the No. 4 camshaft sub-assembly with a wrench and remove the 2 bolts, camshaft timing gear sub-assembly, camshaft timing sprocket and No. 2 chain sub-assembly.

NOTICE:
·

Do not damage the surrounding parts.

·

Do not disassemble the camshaft timing gear sub-assembly.




Hide 13560A 49.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A326617

Remove the bolt and No. 3 chain tensioner assembly.


Hide 50.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.
A326618

Rotate the camshaft and No. 2 camshaft counterclockwise and set the camshaft and No. 2 camshaft as shown in the illustration.


b.
A326619C02
0.51,0.469 0.677,0.635 0.167,0.167 10 true 3 1.281,0.469 1.448,0.635 0.167,0.167 10 true 7 2,0.458 2.198,0.625 0.198,0.167 10 true 15 3.094,0.396 3.292,0.563 0.198,0.167 10 true 11 0.531,1.177 0.677,1.344 0.146,0.167 10 true 2 1.073,1.229 1.219,1.396 0.146,0.167 10 true 4 1.302,1.135 1.448,1.302 0.146,0.167 10 true 6 1.823,1.229 1.969,1.396 0.146,0.167 10 true 8 2.042,1.146 2.219,1.344 0.177,0.198 10 true 14 2.583,1.24 2.76,1.438 0.177,0.198 10 true 16 3.188,1 3.365,1.198 0.177,0.198 10 true 12 3.188,1.26 3.365,1.458 0.177,0.198 10 true 10 1.073,1.958 1.25,2.156 0.177,0.198 10 true 1 1.844,1.958 2.021,2.156 0.177,0.198 10 true 5 2.531,1.948 2.708,2.146 0.177,0.198 10 true 13 3.083,1.958 3.26,2.156 0.177,0.198 10 true 9
V100135

Bolt A
V100136

Bolt B


Uniformly loosen the 16 bolts in the sequence shown in the illustration and remove the bolts and 8 camshaft bearing caps.


Hide 13511 51.REMOVE CAMSHAFT

a.

Remove the camshaft.


Hide 13512 52.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft.


Hide 11811 53.REMOVE NO. 1 CAMSHAFT BEARING

a.
A158703

Remove the No. 1 camshaft bearing from the camshaft bearing cap.


Hide 11821 54.REMOVE NO. 2 CAMSHAFT BEARING

a.
A158539

Remove the No. 2 camshaft bearing from the cylinder head sub-assembly.


Hide 55.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A326620C02
0.063,0.552 0.271,0.729 0.208,0.177 10 true 11 0.063,0.99 0.271,1.167 0.208,0.177 10 true 12 0.052,1.25 0.26,1.427 0.208,0.177 10 true 10 0.115,1.656 0.271,1.854 0.156,0.198 10 true 9 1.406,0.458 1.615,0.635 0.208,0.177 10 true 15 2.135,0.469 2.344,0.646 0.208,0.177 10 true 7 2.885,0.458 3.094,0.635 0.208,0.177 10 true 3 0.896,1.271 1.104,1.417 0.208,0.146 10 true 16 1.354,0.979 1.563,1.125 0.208,0.146 10 true 14 1.615,1.25 1.781,1.427 0.167,0.177 10 true 8 2.115,1.104 2.281,1.281 0.167,0.177 10 true 6 2.406,1.26 2.573,1.438 0.167,0.177 10 true 4 2.875,1.177 3.042,1.354 0.167,0.177 10 true 2 0.938,1.948 1.146,2.094 0.208,0.146 10 true 13 1.646,1.969 1.854,2.115 0.208,0.146 10 true 5 2.417,1.958 2.625,2.104 0.208,0.146 10 true 1
V100135

Bolt A
V100136

Bolt B


Uniformly loosen the 16 bolts in the sequence shown in the illustration and remove the bolts and 8 camshaft bearing caps.


Hide 13053 56.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

a.

Remove the No. 3 camshaft sub-assembly.


Hide 13054 57.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

a.

Remove the No. 4 camshaft sub-assembly.


Hide 11101 58.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11116 61.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 16332 62.REMOVE NO. 1 WATER OUTLET PIPE

Hide 64.REMOVE TAPER SCREW PLUG

NOTICE:

It is not necessary to remove a taper screw plug unless it is being replaced.


a.
A326621

Remove the taper screw plug.


Hide 65.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A328438

Using an E6 "TORX" wrench, remove the 4 stud bolts.