Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2016.08
RM25T0E _58 Vehicle Interior _029927 METER / GAUGE / DISPLAY _0137559 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Gauge Malfunction  


DESCRIPTION

The combination meter receives an engine coolant temperature signal from the ECM*1 engine coolant temperature sensor*2 or water temperature sender gauge assembly*3. The engine coolant temperature gauge needle position changes based on the resistance of the ECM*1 engine coolant temperature sensor*2 or water temperature sender gauge assembly*3.

*1: for 1GR-FE

*2: for 1VD-FTV

*3: for 1HZ


WIRING DIAGRAM

E224935E14
4.875,1.865 6.594,2.073 1.719,0.208 10 false L25 4.875,2.031 6.063,2.375 1.188,0.344 10 false Combination Meter Assembly 5.094,1.063 6.813,1.271 1.719,0.208 10 false S 4.813,0.948 6.531,1.156 1.719,0.208 10 false 11 2.188,0.948 3.906,1.156 1.719,0.208 10 false 12 1.667,1.063 3.385,1.271 1.719,0.208 10 false THWO 1.521,1.865 3.177,2.167 1.656,0.302 10 false I84*1, A29*2 1.521,2.01 3.49,2.323 1.969,0.313 10 false ECM 0.156,0.135 1.875,0.344 1.719,0.208 12 false for 1GR-FE: 0.167,1.875 1.823,2.177 1.656,0.302 10 false *1: for LHD 0.167,2.26 1.823,2.563 1.656,0.302 10 false *2: for RHD

E300846E01
5.521,1.865 5.979,2.063 0.458,0.198 10 false L25 5.521,2.042 6.729,2.406 1.208,0.365 10 false Combination Meter Assembly 5.625,1.115 6.833,1.479 1.208,0.365 10 false FR 0.198,0.135 1.406,0.5 1.208,0.365 12 false for 1VD-FTV: 3.031,1.01 4.24,1.375 1.208,0.365 10 false 3 2.01,1.469 3.844,1.865 1.833,0.396 10 false C69 2.01,1.635 3.844,2.031 1.833,0.396 10 false Engine Coolant Temperature Sensor 5.365,1.021 6.573,1.385 1.208,0.365 10 false 18

E300846E02
5.521,1.865 5.979,2.063 0.458,0.198 10 false L25 5.521,2.042 6.729,2.406 1.208,0.365 10 false Combination Meter Assembly 5.625,1.115 6.833,1.479 1.208,0.365 10 false FR 0.198,0.135 1.406,0.5 1.208,0.365 12 false for 1HZ: 3.031,1.01 4.24,1.375 1.208,0.365 10 false 1 2.01,1.458 3.844,1.854 1.833,0.396 10 false C85 2.01,1.625 3.677,2.063 1.667,0.438 10 false Water Temperature Sender Gauge Assembly 5.365,1.021 6.573,1.385 1.208,0.365 10 false 18

PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for 1GR-FE A
for 1VD-FTV B
for 1HZ C



A

2.CHECK COMBINATION METER ASSEMBLY

B

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR

C

6.CHECK WATER TEMPERATURE SENDER GAUGE ASSEMBLY
2.CHECK COMBINATION METER ASSEMBLY
a.
E293693C03
0.208,1.198 0.667,1.427 0.458,0.229 0.563,0.844 0.729,0.844 0.729,0.844 1.208,1.198 true 0.073,0.146 0.385,0.302 0.313,0.156 10 false *a 0.115,2.302 0.427,2.458 0.313,0.156 10 false *b 0.323,1.229 0.635,1.385 0.313,0.156 10 false L25 0.417,0.75 0.729,0.906 0.313,0.156 10 false S 2.719,3.49 3.042,3.667 0.323,0.177 10 false GND 2.021,3.021 2.344,3.198 0.323,0.177 10 false A 1.292,3.021 1.615,3.198 0.323,0.177 10 false A
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.


b.

Using an oscilloscope, check the signal waveform of the meter.

Measurement Condition
Item Content
Tester Connection L25-11 (S) - Body ground
Tool Setting 5 V/DIV., 10 msec./DIV.
Condition Engine idling

HINT:

As the coolant temperature rises, the period "A" shown in the illumination becomes longer.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the I84*1 or A29*2 ECM connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L25-11 (S) - I84-12 (THWO) Always Below 1 Ω
L25-11 (S) or I84-12 (THWO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L25-11 (S) - A29-12 (THWO) Always Below 1 Ω
L25-11 (S) or A29-12 (THWO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

b.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ENGINE COOLANT TEMPERATURE SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the C69 engine coolant temperature sensor connector.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-18 (FR) - C69-3 Always Below 1 Ω
L25-18 (FR) or C69-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WATER TEMPERATURE SENDER GAUGE ASSEMBLY
a.

Remove the water temperature sender gauge assembly.

Click hereEngine / Hybrid System>1HZ (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


b.

Inspect the water temperature sender gauge assembly.

Click hereEngine / Hybrid System>1HZ (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WATER TEMPERATURE SENDER GAUGE ASSEMBLY)

NG

REPLACE WATER TEMPERATURE SENDER GAUGE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WATER TEMPERATURE SENDER GAUGE ASSEMBLY)
a.

Disconnect the L25 combination meter assembly connector.


b.

Disconnect the C85 water temperature sender gauge assembly connector.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-18 (FR) - C85-1 Always Below 1 Ω
L25-18 (FR) or C85-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR