1.DRAIN TRANSFER OIL
36112B 2.REMOVE REAR NO. 1 TRANSFER CASE HOSE
Disconnect the rear No. 1 transfer case hose from the 2 clamps.
Slide the clip to remove the rear No. 1 transfer case hose.
33403D 3.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)
Remove the bolt and speedometer driven hole cover sub-assembly.
Remove the O-ring from the speedometer driven hole cover sub-assembly.
4.REMOVE SPEEDOMETER DRIVEN GEAR SUB-ASSEMBLY (w/o ABS)
Remove the bolt and speedometer driven gear sub-assembly.
36336 5.REMOVE TRANSFER HEAT INSULATOR (w/ ABS)
84222 6.REMOVE NO .1 TRANSFER INDICATOR SWITCH (4WD Position)
36275 7.REMOVE SHIFT DETENT BALL SPRING PLUG
for Front Transfer Case Side:
Remove the bolt and bracket from the front transfer case.
Using a T40 "TORX" socket wrench, remove the shift detent ball spring plug.
| *1 | Shift Detent Ball Compression Spring |
| *2 | Shift Detent Ball |
Using a magnet hand, remove the shift detent ball compression spring and shift detent ball.
Using a T40 "TORX" socket wrench, remove the 2 shift detent ball spring plugs.
for Front Transfer Extension Housing Side:
Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER CASE FRONT OIL SEAL>REPLACEMENT
33309 8.REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
33481P 9.REMOVE TRANSFER SPEEDOMETER DRIVE GEAR
Remove the transfer speedometer drive gear from the transfer output shaft companion flange sub-assembly.
33309A 10.REMOVE DUST DEFLECTOR
| *a | Turn |
| *b | Hold |
Using SST, remove the dust deflector from the transfer output shaft companion flange sub-assembly.
36105 11.REMOVE FRONT TRANSFER EXTENSION HOUSING SUB-ASSEMBLY
84222 12.REMOVE NO .1 TRANSFER INDICATOR SWITCH (L4 POSITION) (w/ ABS)
36111F 13.REMOVE TRANSFER CASE PLUG
Remove the transfer case plug and gasket from the rear transfer extension housing sub-assembly.
36109B 14.REMOVE REAR TRANSFER EXTENSION HOUSING SUB-ASSEMBLY
w/ ABS:
Remove the 7 bolts and rear transfer extension housing sub-assembly.
If necessary, tap the rear transfer extension housing sub-assembly with a plastic-faced hammer.
w/o ABS:
Remove the 9 bolts and rear transfer extension housing sub-assembly.
If necessary, tap the rear transfer extension housing sub-assembly with a plastic-faced hammer.
| *1 | Transfer Output Rear Case Plate Washer |
| *2 | Transfer Idler Gear Plate Washer |
Remove the transfer output rear case plate washer and transfer idler gear plate washer.
36255 15.REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER
| *1 | No. 1 Transfer Output Shaft Spacer |
| *2 | Transfer Output Rear Shaft Plate Washer |
Remove the No. 1 transfer output shaft spacer with 2 transfer output rear shaft plate washers.
36122 16.REMOVE NO. 2 TRANSFER CASE COVER
Remove the 5 bolts and bracket.
Using a brass bar and hammer, remove the No. 2 transfer case cover.
36112 17.REMOVE REAR TRANSFER CASE
Using a snap ring expander, remove the transfer input gear shaft snap ring.
Remove the 8 bolts and bracket.
Using a brass bar and hammer, remove the rear transfer case.
33124B 18.REMOVE REAR TRANSFER CASE OIL RECEIVER PIPE
Remove the bolt and rear transfer case oil receiver pipe from the rear transfer case.
33124E 19.REMOVE TRANSFER OIL RECEIVER PIPE
for Rear Transfer Case Side:
Remove the bolt and transfer oil receiver pipe.
for Front Transfer Case Side:
Remove the bolt and transfer oil receiver pipe.
for Front Transfer Extension Housing Side:
Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER CASE FRONT OIL SEAL>REPLACEMENT
20.REMOVE INPUT SHAFT ASSEMBLY
Using a plastic-faced hammer, tap the front transfer case and remove the input shaft assembly.
21.REMOVE OUTPUT SHAFT ASSEMBLY
| *1 | Idler Gear Assembly |
| *2 | Output Shaft Assembly |
| *3 | No. 1 Transfer Gear Shift Fork and Transfer High and Low Shift Fork Shaft |
Remove the idler gear assembly and output shaft assembly together with the No. 1 transfer gear shift fork and transfer high and low shift fork shaft.
36236 22.REMOVE FRONT DRIVE CLUTCH SLEEVE
Remove the front drive clutch sleeve with the No. 2 transfer gear shift fork and transfer front drive shift fork shaft.
36312F 23.REMOVE NO. 2 TRANSFER GEAR SHIFT FORK
Using 2 screwdrivers and a hammer, tap out the 2 transfer gear shift fork shaft snap rings.
Remove the No. 2 transfer gear shift fork and shift detent ball compression spring from the transfer front drive shift fork shaft.
36311F 24.REMOVE NO. 1 TRANSFER GEAR SHIFT FORK
Using a pin punch and hammer, tap out the transfer shift fork slotted spring pin.
Remove the No. 1 transfer gear shift fork from the transfer high and low shift fork shaft.
36362A 25.REMOVE TRANSFER SHIFT OUTER LEVER
Remove the nut and washer from the transfer shift outer lever.
| *1 | Lever Lock Pin |
Using a brass bar and hammer, tap out the lever lock pin.
| *1 | Transfer Shift Outer Lever |
| *2 | Transfer Shift Inner Lever Shaft |
| *3 | Washer |
Remove the transfer shift outer lever, washer and transfer shift inner lever shaft.
| *1 | Transfer Shift Lever Inner |
| *2 | Transfer Shift Inner Lever Shaft |
| *3 | E-Ring |
| *a | Protective Tape |
Using a screwdriver, remove the E-ring and transfer shift lever inner from the transfer shift inner lever shaft.
Tape the screwdriver tip before use.
36111B 26.REMOVE TRANSFER CASE OIL SEAL
| *a | Protective Tape |
for Transfer Shift Inner Lever Shaft Side:
Using a screwdriver, remove the transfer case oil seal.
Tape the screwdriver tip before use.
for Input Shaft Side:
Using SST and a hammer, remove the transfer case oil seal.
36231C 27.REMOVE TRANSFER OUTPUT SHAFT TAPER ROLLER BEARING
for Front Transfer Case Side:
Using a brass bar and hammer, remove the transfer output shaft taper roller bearing (outer race) from the front transfer case.
for Rear Transfer Case Side:
Remove the transfer output shaft taper roller bearing (outer race) from the rear transfer case.
36221G 28.REMOVE TRANSFER ILDER GEAR BEARING (for Front Side)
Using SST, remove the transfer idler gear bearing (outer race) from the front transfer case.
| *a | Turn |
| *b | Hold |
Using SST and a press, remove the transfer idler gear bearing (inner race) from the idler gear assembly.
Support the idler gear assembly by hand to prevent it from dropping.
Remove the 3 bolts and transfer idler gear transfer oil receiver.
36221H 29.REMOVE TRANSFER ILDER GEAR BEARING (for Rear Side)
Remove the transfer idler gear bearing (outer race) from the rear transfer case.
| *a | Turn |
| *b | Hold |
Using SST and a press, remove the transfer idler gear bearing (inner race) from the idler gear assembly.
Support the idler gear assembly by hand to prevent it from dropping.
36212A 30.REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING
Using a snap ring expander, remove the transfer input bearing shaft snap ring.
Using SST and a press, remove the transfer input gear radial ball bearing.
Support the output shaft assembly by hand to prevent it from dropping.
36212F 31.REMOVE FRONT TRANSFER INPUT SHAFT RADIAL BALL BEARING
Using a snap ring expander, remove the shaft snap ring.
Using SST and a press, remove the front transfer input shaft radial ball bearing.
Support the input shaft assembly by hand to prevent it from dropping.
36245 32.REMOVE FRONT TRANSFER DRIVE GEAR PIECE
Using a snap ring expander, remove the transfer output shaft shaft snap ring.
Using SST and a press, remove the front transfer drive gear piece from the output shaft assembly.
Support the output shaft assembly by hand to prevent it from dropping.
36242 33.REMOVE TRANSFER LOW GEAR
Using a press, remove the transfer low gear and transfer output shaft taper roller bearing (inner race) from the output shaft assembly.
Support the output shaft assembly by hand to prevent it from dropping.
Remove the transfer output shaft front needle roller bearing from the output shaft assembly.
36203 34.REMOVE TRANSFER HIGH SPEED OUTPUT GEAR SUB-ASSEMBLY
Using SST and a press, remove the transfer output shaft taper roller bearing (inner race) from the output shaft assembly.
Support the output shaft assembly by hand to prevent it from dropping.
Remove the transfer high speed output gear sub-assembly from the output shaft assembly.
Remove the 2 pieces of the front transfer output shaft needle roller bearing and No. 1 transfer output shaft spacer.
36231E 35.REMOVE FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING
Using SST, remove the front transfer output shaft needle roller bearing.
36247 36.REMOVE TRANSFER SYNCHRONIZER RING
36235 37.REMOVE TRANSFER HIGH AND LOW CLUTCH SLEEVE
| *a | Protective Tape |
Using a screwdriver, remove the 2 transfer synchromesh shifting key springs.
Tape the screwdriver tip before use.
Remove the transfer high and low clutch sleeve and the 3 No. 2 synchromesh shifting keys.
36237 38.REMOVE TRANSFER CLUTCH HUB
Using 2 screwdrivers and a hammer, remove the transfer clutch hub shaft snap ring.
Using a press, remove the transfer clutch hub.
36239 39.REMOVE TRANSFER DRIVE CLUTCH HUB
36209A 40.REMOVE FRONT TRANSFER OUTPUT SHAFT
36104B 41.REMOVE TRANSFER OUTPUT SHAFT DUST DEFLECTOR
| *a | Turn |
| *b | Hold |
Using SST, remove the transfer output shaft dust deflector.
33325B 42.REMOVE FRONT TRANSFER EXTENSION HOUSING DUST DEFLECTOR
| *a | Protective Tape |
Using a screwdriver and hammer, remove the front transfer extension housing dust deflector.
Tape the screwdriver tip before use.
36105A 43.REMOVE FRONT TRANSFER EXTENSION HOUSING OIL SEAL
36231H 44.REMOVE FRONT TRANSFER OUTPUT SHAFT RADIAL BALL BEARING
36109C 45.REMOVE REAR TRANSFER EXTENSION HOUSING OIL SEAL