Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for RHD) › from 2016.08
RM25T0E _52 Drivetrain _029901 CLUTCH _0136565 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 31301F 1.INSTALL CLUTCH PEDAL STOPPER BOLT (for 1GR-FE, 1HZ)

a.
C210605

Install the lock nut to the clutch pedal stopper bolt.


b.

Temporarily install the clutch pedal stopper bolt to the clutch pedal support sub-assembly.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 88280A 2.INSTALL CLUTCH SWITCH ASSEMBLY (for 1VD-FTV)

a.
C210602

Install the lock nut to the clutch switch assembly.


b.

Temporarily install the clutch switch assembly to the clutch pedal support sub-assembly.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 31353 3.INSTALL CLUTCH PEDAL SPRING HOLDER

a.
C310592C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the clutch pedal spring holder.


b.

Install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 31453B 4.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.
C310593C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of a new clutch master cylinder push rod clevis bush.


b.

Install the clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

HINT:

Install the clevis bush from the right side of the vehicle.



Hide 31301P 5.INSTALL CLUTCH PEDAL TURNOVER BUSH

a.
C310594C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of the clutch pedal turnover bush.


b.

Install the clutch pedal turnover bush to the clutch pedal sub-assembly.


Hide 31301B 6.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.
C210598

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31301C 7.INSTALL CLUTCH PEDAL BUSH

a.
C310595C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside and outside of 2 new clutch pedal bushes.


b.

Install the 2 clutch pedal bushes to the clutch pedal sub-assembly.


Hide 31324A 8.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C310596C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the clutch pedal shaft collar.


b.

Install the clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 31321 9.INSTALL CLUTCH PEDAL PAD

Hide 31301 10.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.
C210595

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Install the bolt from the right side of the vehicle.



Hide 31301A 11.INSTALL CLUTCH PEDAL SPRING (for 1GR-FE, 1VD-FTV)

a.
C310597C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside and outside of the spacer and pin of the clutch pedal support sub-assembly.


b.

Install the spacer to the clutch pedal spring.


c.

Install the clutch pedal spring to the clutch pedal support sub-assembly with 2 new E-rings.


Hide 31301R 12.INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING

a.
C310598C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surfaces of the clutch pedal spring holder, clutch pedal and turn over spring seat compression spring.


b.

Move the pedal to the full stroke position.


c.

Install the turn over spring seat compression spring to the clutch pedal sub-assembly and clutch pedal spring holder.


Hide 13.TEMPORARILY INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY

a.
C212396

Install the clutch pedal sub-assembly on the vehicle, and then temporarily install the bolt.


b.

for 1VD-FTV:

Connect the clutch switch connector.


Hide 31410 14.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.

Install a new gasket.


b.
C163255

Install the clutch master cylinder assembly with the 2 nuts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


c.

Tighten the clutch pedal support fixed bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

for 1VD-FTV:

Connect the clutch switch connector.


e.
C163271C03
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the clutch master cylinder push rod clevis pin.


f.

Connect the clevis of the master cylinder to the clutch pedal with the clutch master cylinder push rod clevis pin.


g.

Install a new clip to the clutch master cylinder push rod clevis pin.


h.
C310599C01
1.656,1.76 1.875,1.958 0.219,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the clutch master cylinder to flexible hose tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




Hide 55844 15.INSTALL NO. 2 HEATER TO REGISTER DUCT

Hide 73900 16.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55480D 17.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (w/o Knee Airbag)

Hide 18.FILL RESERVOIR WITH BRAKE FLUID

Hide 19.BLEED CLUTCH PIPE LINE

Hide 20.CHECK FLUID LEVEL IN RESERVOIR

Hide 21.CHECK FOR CLUTCH FLUID LEAK

Hide 31301 22.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY