Refer to DTC P2120.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P2120
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2121 | Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance | The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic) |
·
Accelerator pedal position sensor circuit
·
Accelerator pedal sensor assembly
·
ECM |
Comes on | DTC stored |
Refer to DTC P2120.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P2120
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
| *1 | Accelerator Pedal |
| *a | Depressed |
| *b | Released |
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
| Tester Display |
|---|
| Accel Sens. No.1 Volt % |
| Accel Sens. No.2 Volt % |
Read the values.
| Accelerator Pedal | Accel Sens. No. 1 Volt % | Accel Sens. No. 2 Volt % |
|---|---|---|
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| Proceed to |
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
NG
| *a | Front view of wire harness connector (to Accelerator Pedal Sensor Assembly) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the A29 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I43-1 (VCP2) - A29-56 (VCP2) | Always | Below 1 Ω |
| I43-2 (EPA2) - A29-58 (EPA2) | Always | Below 1 Ω |
| I43-3 (VPA2) - A29-54 (VPA2) | Always | Below 1 Ω |
| I43-4 (VCPA) - A29-55 (VCPA) | Always | Below 1 Ω |
| I43-5 (EPA) - A29-57 (EPA) | Always | Below 1 Ω |
| I43-6 (VPA) - A29-53 (VPA) | Always | Below 1 Ω |
| I43-1 (VCP2) or A29-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
| I43-2 (EPA2) or A29-58 (EPA2) - Body ground | Always | 10 kΩ or higher |
| I43-3 (VPA2) or A29-54 (VPA2) - Body ground | Always | 10 kΩ or higher |
| I43-4 (VCPA) or A29-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| I43-5 (EPA) or A29-57 (EPA) - Body ground | Always | 10 kΩ or higher |
| I43-6 (VPA) or A29-53 (VPA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.
Clear the DTC.
Start the engine.
Allow the engine to idle for 15 seconds.
Depress and release the accelerator pedal several times.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTC.
| Result | Proceed to |
|---|---|
| P2121 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
| NEXT |
NEXT