Refer to DTC P0545.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0545
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P242C | Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3 | No. 3 exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·
After starting the engine, 11 minutes or more elapses
·
Coolant temperature is 70°C (158°F) or higher
·
The No. 2 exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds. |
·
Open or short in No. 3 exhaust gas temperature sensor circuit
·
No. 3 exhaust gas temperature sensor
·
ECM |
Comes on | DTC stored |
| P242D | Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3 | No. 3 exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·
After starting the engine, 11 minutes or more elapses
·
Coolant temperature is 70°C (158°F) or higher
·
The No. 2 exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds. |
·
Open or short in No. 3 exhaust gas temperature sensor circuit
·
No. 3 exhaust gas temperature sensor
·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P242C | Exhaust Temperature B1S3 |
| P242D |
DTC P20CF (exhaust fuel addition injector assembly malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.
Sensor 3 represents the sensor located downstream of the DPF catalytic converter.
When DTC P242C and P242D are output, check the downstream exhaust gas temperature indicated by "Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S3" using the GTS.
| Condition | Exhaust Temperature B1S3 | No. 3 Exhaust Gas Temperature Sensor Condition |
|---|---|---|
| Idling with warm engine | Constant at between 50 and 700°C (122 and 1292°F) | Normal |
| 0°C (32°F) | Open circuit | |
| 1000°C (1832°F) | Short circuit |
The ECM constantly monitors the output voltages from the No. 3 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P242C | Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), the No. 2 exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine. |
| P242D |
Refer to DTC P0545.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0545
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
If DTC P242D is stored and the No. 3 exhaust gas temperature sensor circuit is not malfunctioning, check if the exhaust manifold converter sub-assembly has melted as DTC P242D may be stored when the exhaust manifold converter sub-assembly melts and the No. 3 exhaust gas temperature sensor is exposed to high temperatures.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S3 |
Read the value.
Same as the actual No. 3 exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with thr warm engine), the exhaust temperature varies after an engine speed of 3000 rpm is maintained for 1 minute.
| Temperature Displayed | Proceed to |
|---|---|
| 0°C (32°F) (After warming up the engine) | A |
| 1000°C (1832°F) or higher | B |
| Same as the actual exhaust gas temperature | C |
If there is a short circuit, the GTS will indicate 0°C (32°F).
If there is an open circuit, the GTS will indicate 1000°C (1832°F).
A
B
C
| *1 | No. 3 Exhaust Gas Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector (to No. 3 Exhaust Gas Temperature Sensor) |
Disconnect the No. 3 exhaust gas temperature sensor connector.
Connect terminals 1 and 2 of the exhaust gas temperature sensor connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S3 |
Read the value.
1000°C (1832°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 3 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 3 exhaust gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C120-2 (THCO) - C39-123 (THCO) | Always | Below 1 Ω |
| C120-1 (E2) - C39-99 (ETCF) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | No. 3 Exhaust Gas Temperature Sensor |
| *2 | ECM |
Disconnect the No. 3 exhaust gas temperature sensor connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S3.
| Tester Display |
|---|
| Exhaust Temperature B1S3 |
Read the value.
0°C (32°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 3 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 3 exhaust gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C120-2 (THCO) or C39-123 (THCO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), the No. 2 exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT