Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P1626  Idle Signal Output Value Too Low  P1627  Idle Signal Output Value Too High  P1629  Idol Signal Output Value Too Low Bank2  P162A  Idol Signal Output Value Too High Bank2  


DESCRIPTION

The ECM reduces fuel injector operation speed and applied voltage to the fuel injector to reduce the sound it produces during idling. To do this, the ECM outputs applied voltage switching signals to terminal IJEN of the injector driver from terminal IDLO and IDL2 of the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1626 Idle Signal Output Value Too Low With the engine running at idle, voltage of the ECM IDLO or IDL2 terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver

·

ECM


Comes on DTC stored
P1627 Idle Signal Output Value Too High With the engine running at speeds higher than idle, voltage of the ECM IDLO or IDL2 terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver

·

ECM


Comes on DTC stored
P1629 Idol Signal Output Value Too Low Bank2 With the engine running at idle, voltage of the ECM IDLO or IDL2 terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver

·

ECM


Comes on DTC stored
P162A Idol Signal Output Value Too High Bank2 With the engine running at speeds higher than idle, voltage of the ECM IDLO or IDL2 terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1626
P1627
P1629
P162A
Warm up the engine and idle it for 5 seconds

WIRING DIAGRAM

A275257E03
6.115,2.219 6.51,2.406 0.396,0.188 10 false C39 6.115,2.427 6.469,2.594 0.354,0.167 10 false ECM 5.885,0.521 6.281,0.667 0.396,0.146 10 false IDLO 5.573,0.417 5.771,0.573 0.198,0.156 10 false 59 1.5,0.406 1.625,0.563 0.125,0.156 10 false 7 1.042,0.49 1.375,0.667 0.333,0.177 10 false IJEN 0.583,1.167 2.313,1.333 1.729,0.167 10 false No. 1 Injector Driver (EDU) 0.552,0.99 0.938,1.177 0.385,0.188 10 false C122 5.875,1.823 6.271,1.969 0.396,0.146 10 false IDL2 5.563,1.719 5.76,1.875 0.198,0.156 10 false 58 1.51,1.719 1.635,1.875 0.125,0.156 10 false 7 1.052,1.792 1.385,1.969 0.333,0.177 10 false IDL2 0.563,2.5 2.292,2.667 1.729,0.167 10 false No. 2 Injector Driver (EDU) 0.542,2.323 0.927,2.51 0.385,0.188 10 false C125

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
a.

Disconnect the No. 1 or No. 2 injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C122-7 (IJEN) - C39-59 (IDLO) Always Below 1 Ω
C125-7 (IDL2) - C39-58 (IDL2) Always Below 1 Ω
C122-7 (IJEN) or C39-59 (IDLO) - Body ground Always 10 kΩ or higher
C122-7 (IJEN) or C39-59 (IDLO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE INJECTOR DRIVER

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE INJECTOR DRIVER
·

When DTC P1626 or P1627 is output:

Replace the No. 1 injector driver.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL

·

When DTC P1629 or P162A is output:

Replace the No. 2 injector driver.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK ANY OTHER DTCS OUTPUT
3.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.


Result:
Result Proceed to
P1626 or P1627 is output A
No DTC is output B



A

4.REPLACE ECM

B

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

After warming up the engine, idle the engine for 5 seconds or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED