Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2084  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2  P242B  Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3  


DESCRIPTION

Refer to DTC P0545.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0545

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2

All conditions are met (2 trip detection logic):

(a)

The battery voltage is 8 V or higher.

(b)

After the engine is stopped and the vehicle is left as is for 10 hours or more, the difference between "Exhaust Temperature B1S2" and "Coolant Temp" is 400°C (752 °F) or more when the ignition switch is turned to ON.



·

No. 2 exhaust gas temperature sensor

·

Engine coolant temperature sensor

·

ECM (soak timer)


Comes on DTC stored
P242B Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3

All conditions are met (2 trip detection logic):

(a)

The battery voltage is 8 V or higher.

(b)

After the engine is stopped and the vehicle is left as is for 10 hours or more, the difference between "Exhaust Temperature B1S3" and "Coolant Temp" is 400°C (752 °F) or more when the ignition switch is turned to ON.



·

No. 3 exhaust gas temperature sensor

·

Engine coolant temperature sensor

·

ECM (soak timer)


Comes on DTC stored

Related Data List
DTC No. Data List
P2084
P242B
·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3

·

Coolant Temp

·

Intake Air



HINT:
·

Sensor 2 represents the sensor located upstream of the DPF catalytic converter.

·

Sensor 3 represents the sensor located downstream of the DPF catalytic converter.

·

If DTC P2084 is stored, the following symptoms may appear:

-

White smoke




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2084 Stop the engine, leave the vehicle as is for 1 to 2 hours and confirm that "Exhaust Temperature B1S2" is approximately the same value as "Intake Air".
P242B Stop the engine, leave the vehicle as is for 1 to 2 hours and confirm that "Exhaust Temperature B1S3" is approximately the same value as "Intake Air".

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2084 OR P242B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
DTC P2084 or P242B is output A
Except above, DTC P2084 or P242B and other DTCs are output B




A

2.READ VALUE USING GTS (EXHAUST TEMPERATURE)

B

2.READ VALUE USING GTS (EXHAUST TEMPERATURE)
a.

Leave the vehicle as is for 1 to 2 hours with the engine stopped.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

Powertrain > Engine and ECT > Data List
Tester Display
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 234 859,860

e.

Read the values.

Result:
Result Proceed to
Value of "Exhaust Temperature B1S2" is 400°C (752°F) or higher A
Value of "Exhaust Temperature B1S3" is 400°C (752°F) or higher
Except above B


HINT:

If the exhaust gas temperature sensor is normal, the exhaust gas temperature drops when the vehicle is left as is for 1 to 2 hours with the engine stopped. If the exhaust gas temperature does not drop, the exhaust gas temperature sensor may be malfunctioning.




A

3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

B

5.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
3.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the exhaust gas temperature sensor.

·

When DTC P2084 is output:

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for DPF)>REMOVAL

·

When DTC P242B is output:

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for DPF)>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Leave the vehicle as is for 1 to 2 hours with the engine stopped.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Exhaust Temperature B1S2, Exhaust Temperature B1S3 and Intake Air.

Powertrain > Engine and ECT > Data List
Tester Display
Exhaust Temperature B1S2
Exhaust Temperature B1S3
Intake Air
50003 234 859,860,5

e.

Read the value.

OK:

The values of "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" are all approximately the same as "Intake Air".



Result:
Proceed to
NEXT



NEXT

END

5.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Coolant temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value.

OK:

The difference between the displayed value and outside air temperature is below 5°C (9°F).


NOTICE:

If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

7.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED