Refer to DTCs C1401 and C1402.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1405 | Open or Short in Front Speed Sensor RH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more.
2.
With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor RH
·
Skid control ECU (Brake actuator assembly)
·
Wire harness or connector
·
Skid control sensor wire RH |
| C1406 | Open or Short in Front Speed Sensor LH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more.
2.
With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor LH
·
Skid control ECU (Brake actuator assembly)
·
Wire harness or connector
·
Skid control sensor wire LH |
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Normal or Error | Normal | Error: Momentary interruption |
| FL Speed Open | Front speed sensor LH open detection | Normal or Error | Normal | Error: Momentary interruption |
| Tester Display |
|---|
| FR Speed Open |
| FL Speed Open |
Normal (There are no momentary interruptions).
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph) Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is recorded.
| Proceed to |
|---|
| DTCs C1405 and C1406 are not output |
| DTCs C1405 and/or C1406 are output |
DTCs C1405 and C1406 are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTCs C1405 and/or C1406 are output
Turn the ignition switch off.
Remove the skid control sensor wire.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ VSC)>REMOVAL
| *A | for RH (Type A) |
| *B | for RH (Type B) |
| *C | for LH |
| *1 | Skid Control Sensor Wire |
| *a | Front view of wire harness connector (to Sensor Side Connector) |
| *b | Front view of wire harness connector (to Vehicle Side Connector) |
| *c | Male |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B3 male connector 1 (FR-) - A-1 (FR-) | Always | Below 1 Ω |
| B3 male connector 1 (FR-) or A-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| B3 male connector 2 (FR+) - A-3 (FR+) | Always | Below 1 Ω |
| B3 male connector 2 (FR+) or A-3 (FR+) - Body ground | Always | 10 kΩ or higher |
| A-1 (FR-) - A-3 (FR+) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B4 male connector 1 (FR-) - A-1 (FR-) | Always | Below 1 Ω |
| B4 male connector 1 (FR-) or A-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| B4 male connector 3 (FR+) - A-3 (FR+) | Always | Below 1 Ω |
| B4 male connector 3 (FR+) or A-3 (FR+) - Body ground | Always | 10 kΩ or higher |
| A-1 (FR-) - A-3 (FR+) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21 male connector 1 (FL-) - B-1 (FL-) | Always | Below 1 Ω |
| A21 male connector 1 (FL-) or B-1 (FL-) - Body ground | Always | 10 kΩ or higher |
| A21 male connector 3 (FL+) - B-3 (FL+) | Always | Below 1 Ω |
| A21 male connector 3 (FL+) or B-3 (FL+) - Body ground | Always | 10 kΩ or higher |
| B-1 (FL-) - B-3 (FL+) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Install the skid control sensor wire.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ VSC)>INSTALLATION
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Disconnect the A and/or B front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-31 (FR+) - B3-2 (FR+) | Always | Below 1 Ω |
| A42-30 (FR-) - B3-1 (FR-) | Always | Below 1 Ω |
| A42-31 (FR+) or B3-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| A42-30 (FR-) or B3-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-31 (FR+) - B4-3 (FR+) | Always | Below 1 Ω |
| A42-30 (FR-) - B4-1 (FR-) | Always | Below 1 Ω |
| A42-31 (FR+) or B4-3 (FR+) - Body ground | Always | 10 kΩ or higher |
| A42-30 (FR-) or B4-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-18 (FL+) - A21-3 (FL+) | Always | Below 1 Ω |
| A42-17 (FL-) - A21-1 (FL-) | Always | Below 1 Ω |
| A42-18 (FL+) or A21-3 (FL+) - Body ground | Always | 10 kΩ or higher |
| A42-17 (FL-) or A21-1 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Front Speed Sensor) |
Reconnect the A42 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A-3 (FR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B-3 (FL+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG