Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029469 HEATING / AIR CONDITIONING _0137756 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 88510 1.INSTALL COOLER UNIT ASSEMBLY

a.

for LHD:

Install the No. 1 cooler unit drain hose.

E303828C01
5.823,2.604 6.01,2.365 6.01,2.365 6.333,2.365 true 5.979,3.333 5.75,3.333 5.75,3.333 5.76,2.719 true 1.417,2.073 0.792,1.792 0.792,1.792 1.927,0.74 true 5.344,1.25 5.344,0.979 false 6.438,0.365 6.167,0.219 6.167,0.219 5.833,0.219 true 0.583,1.719 0.896,1.875 0.313,0.156 10 false *1 5.271,0.813 5.583,0.969 0.313,0.156 10 false *2 6.031,3.26 6.344,3.417 0.313,0.156 10 false *3 6.354,2.281 6.667,2.438 0.313,0.156 10 false *a 6.031,0.625 6.208,0.823 0.177,0.198 10 true *b 5.896,1.302 6.125,1.5 0.229,0.198 10 true *c 5.667,0.156 5.979,0.313 0.313,0.156 10 false *4 5.167,2.125 5.375,2.302 0.208,0.177 10 true *d
*1 Screw *2 Bolt
*3 No. 1 Cooler Unit Drain Hose *4 Air inlet Damper Control Cable Sub-assembly
*a No. 1 Cooler Unit Drain Hose Paint Mark
for 1HZ: Pink
for 1GR-FE: Yellow
*b RECIRC Side
*c FRESH Side *d Engine Room Side



b.

for RHD:

Install the No. 1 cooler unit drain hose.

E304202C02
1.917,1.24 1.917,1 false 0.719,0.302 1.417,0.302 true 1.021,3.344 1.323,3.344 1.323,3.344 1.5,2.719 true 5.885,2.083 6.219,1.844 6.219,1.844 5.333,0.75 true 1.469,2.594 1.625,2.313 1.625,2.313 1.938,2.313 true 6.292,1.75 6.604,1.906 0.313,0.156 10 false *1 1.833,0.813 2.146,0.969 0.313,0.156 10 false *2 0.854,3.271 1.167,3.427 0.313,0.156 10 false *3 1.469,0.219 1.781,0.375 0.313,0.156 10 false *4 1.958,2.198 2.271,2.354 0.313,0.156 10 false *a 0.302,0.719 0.615,0.875 0.313,0.156 10 false *b 0.354,1.563 0.667,1.719 0.313,0.156 10 false *c 0.667,2.094 0.979,2.25 0.313,0.156 10 false *d
*1 Screw *2 Bolt
*3 No. 1 Cooler Unit Drain Hose *4 Air inlet Damper Control Cable Sub-assembly
*a No. 1 cooler unit drain hose Paint Mark
for 1HZ, 1VD-FTV: Blue
for 1GR-FE: Green
*b RECIRC Side
*c FRESH Side *d Engine Room Side



c.

Install the cooler unit assembly.


d.

Align the link of the cooler unit assembly to the RECIRC side, and then insert the end of the air inlet damper control cable sub-assembly into the link and secure it with the clamp.


e.

Connect the clamps, connectors.


f.

Install the 4 nuts, 2 screws and bolt.

Torque:
for nut and bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 55331 2.INSTALL INSTRUMENT PANEL REINFORCEMENT

a.

Install the instrument panel reinforcement with the 5 bolts and nut.

E355641C01
2.875,1.302 2.875,0.604 2.875,0.604 3.271,0.604 true 1.49,0.479 1.49,0.313 1.49,0.313 1.885,0.313 true 6.115,1.5 5.833,1.781 5.833,1.781 5.5,1.49 true 0.063,0.052 0.375,0.208 0.313,0.156 12 false *A 1.917,0.26 2.229,0.417 0.313,0.156 10 false *1 3.302,0.531 3.615,0.688 0.313,0.156 10 false *2 5.75,1.802 6.063,1.958 0.313,0.156 10 false *3 2.552,0.156 2.865,0.313 0.313,0.156 10 false *a
*A w/o Driver Side Knee Airbag - -
*1 Nut *2 Grommet
*3 Ground Wire - -
*a Engine Room Side - -


E353900C01
5.771,0.604 5.917,0.656 5.917,0.656 6.083,0.656 true 4.198,1.323 3.719,1.323 3.719,1.323 3.719,0.521 true 1.094,0.917 1.406,1.281 1.406,1.281 1.719,0.927 true 4.042,1.323 4.042,0.458 true 0.073,0.083 0.385,0.24 0.313,0.156 12 false *A 6.146,0.594 6.458,0.75 0.313,0.156 10 false *1 4.24,1.24 4.469,1.406 0.229,0.167 10 false *2 1.333,1.302 1.646,1.458 0.313,0.156 10 false *3 2.594,0.292 2.906,0.448 0.313,0.156 10 false *a
*A w/ Driver Side Knee Airbag - -
*1 Nut *2 Grommet
*3 Ground Wire - -
*a Engine Room Side - -



b.

Attach the clamps and instrument panel wire.


c.

Connect the connectors.


d.

Connect the 2 ground wires with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Install the 2 bolts and 2 grommets.


f.

Connect the connectors.


Hide 28520 3.INSTALL PREHEATING TIMER ASSEMBLY (for 1HZ, w/o EGR)

Hide 89551 4.INSTALL EMISSION CONTROL ECU (for 1HZ, w/ EGR)

Hide 5.INSTALL DOOR CONTROL RECEIVER (w/ Wireless Door Lock System)

a.

Connect the connector.


b.

Install the door control receiver with the bolt.


Hide 88650 6.INSTALL COOLER STABILIZER AMPLIFIER ASSEMBLY

a.

Install the cooler stabilizer amplifier assembly with the nut.


b.

Connect the connector.


Hide 55307C 7.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

w/o Driver Side Knee Airbag:

i.

Install the No. 2 instrument panel brace sub-assembly with the 2 nuts and 2 bolts.


ii.

for 1GR-FE, for 1VD-FTV:

Attach the 2 claws to install the DLC3 connector.


iii.

Attach the 2 claws to install the instrument panel wire.



b.

w/ Driver Side Knee Airbag:

i.

Install the No. 2 instrument panel brace sub-assembly with the 2 nuts and 2 bolts.


ii.

Attach the 2 claws to install the DLC3 connector.


iii.

Attach the 2 claws to install the instrument panel wire.



Hide 55306A 8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the 2 nuts and 2 bolts.


Hide 55833D 9.INSTALL NO. 1 INSTRUMENT PANEL REGISTER CONNECTOR

a.

Install the No. 1 instrument panel register connector with the 2 clips.


Hide 55837C 10.INSTALL CENTER HEATER TO REGISTER SUB DUCT

a.

Install the center heater to register sub duct with the screw.


Hide 55834B 11.INSTALL NO. 2 INSTRUMENT PANEL REGISTER CONNECTOR

a.

Install the No. 2 instrument panel register connector together with the No. 5 heater to register duct with the 2 clips.


Hide 12.INSTALL STEERING COLUMN ASSEMBLY

Hide 55301 13.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55792E 14.INSTALL NO. 2 HEATER AIR DUCT HOLE COVER

a.

except Canvas Top:

Attach the 9 claws to install the No. 2 heater air duct hole cover.


b.

for Canvas Top:

Attach the 7 claws to install the No. 2 heater air duct hole cover.


Hide 55781F 15.INSTALL COWL TOP VENTILATOR LOUVER

Hide 16.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 17.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 85192 18.INSTALL WINDSHIELD WIPER ARM COVER

Hide 85190 19.ADJUST WINDSHIELD WIPER ARM ASSEMBLY

Hide 88716C 20.CONNECT COOLER REFRIGERANT LIQUID PIPE C (except Sub-cool Accelerator)

a.

Remove the attached vinyl tape from the cooler refrigerant liquid pipe C.


b.

Sufficiently apply compressor oil to new O-ring and the fitting surface of the cooler refrigerant liquid pipe C.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring on the cooler refrigerant liquid pipe C.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe C.


Hide 88712 21.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (except Sub-cool Accelerator)

a.
E303262C02
1.781,0.74 1.219,0.531 1.219,0.531 0.906,0.531 true 0.75,0.438 1.063,0.594 0.313,0.156 10 false *1
*1 Plate


Remove the attached vinyl tape from the No. 1 cooler refrigerant suction hose.


b.

Sufficiently apply compressor oil to new O-ring and the fitting surface of the No. 1 cooler refrigerant suction hose.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring on the No. 1 cooler refrigerant suction hose.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the No. 1 cooler refrigerant suction hose.


e.

Rotate the hook connector in the direction indicated by the arrow in the illustration and install the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 88710E 22.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for Sub-cool Accelerator)

a.
E303597C01
0.865,0.583 1.177,0.583 1.177,0.583 1.719,0.74 true 0.698,0.521 1.01,0.677 0.313,0.156 10 false *1
*1 Plate


Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioner tube and accessory assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the air conditioner tube and accessory assembly.


e.

Rotate the hook connector in the direction indicated by the arrow in the illustration and install the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 25.CHECK FOR REFRIGERANT GAS LEAK