Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2454  Diesel Particulate Filter Pressure Sensor "A" Circuit Low  P2455  Diesel Particulate Filter Pressure Sensor "A" Circuit High  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

If P2454 and/or P2455 is present, refer to the DTC chart for DPF system.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION


A128654E10
4.438,1.208 4.25,1.385 false 4.583,1.115 4.729,1.313 false 4.406,1.167 4.24,1.208 false 5.333,3.042 5.104,2.552 5.104,2.552 5.146,2.552 false 1.302,2.26 0.802,2.917 false 2.76,2.552 2.885,2.917 false 1.688,1.052 1.688,1.208 false 1.302,0.708 2.125,0.885 0.823,0.177 10 Exhaust Gas 2.917,0.708 3.26,0.875 0.344,0.167 10 ECM 0.375,2.938 1.448,3.271 1.073,0.333 10 DPF Catalytic Converter 2.344,2.938 3.635,3.292 1.292,0.354 10 Differential Pressure Sensor Assembly 3.854,0.052 5.708,0.24 1.854,0.188 10 Property of Output Voltage: 4.76,1.25 5.646,1.417 0.885,0.167 10 Stores P2455 5.156,2.479 6.063,2.646 0.906,0.167 10 Stores P2454 4.052,0.635 6.073,0.813 2.021,0.177 10 Differential Pressure Voltage (V) 4.021,0.938 4.396,1.104 0.375,0.167 10 5.000 3.865,1.135 4.24,1.302 0.375,0.167 10 4.800 3.865,1.333 4.24,1.5 0.375,0.167 10 4.650 4.021,2.344 4.396,2.51 0.375,0.167 10 1.530 4.021,2.563 4.396,2.729 0.375,0.167 10 0.750 4.021,2.719 4.396,2.885 0.375,0.167 10 0.555 4.021,2.865 4.396,3.031 0.375,0.167 10 0.400 4.292,3.115 4.396,3.271 0.104,0.156 10 0 4.771,3.229 4.875,3.385 0.104,0.156 10 0 4.531,3.229 4.708,3.396 0.177,0.167 10 -5 4.938,3.229 5.229,3.396 0.292,0.167 10 20.0 6.469,3.24 6.854,3.406 0.385,0.167 10 100.0 4.323,3.417 6.813,3.615 2.49,0.198 10 Exhaust Gas Differential Pressure (kPa)


The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference between the pressure before and after the DPF catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, sets DTC P2454 or P2455, and illuminates the MIL.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low Differential pressure sensor assembly output voltage is below 0.4 V for 3 seconds or more (1 trip detection logic).
·

Open or short in differential pressure sensor circuit assembly

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored
P2455 Diesel Particulate Filter Pressure Sensor "A" Circuit High Differential pressure sensor assembly output voltage is higher than 4.8 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2454 DPF Differential Pressure
P2455

HINT:
·

DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.

·

After confirming DTC P2454 and P2455, check the differential pressure in the "Powertrain / Engine and ECT / Data List / All Data / DPF Differential Pressure" menu using the GTS.


Reference:
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2454 Ignition switch ON for 5 seconds
P2455

WIRING DIAGRAM

A379958E04
0.698,2.854 1.313,3.052 0.615,0.198 10 false C128 0.688,3.01 2.49,3.208 1.802,0.198 10 false Differential Pressure Sensor 1.479,0.917 1.792,1.115 0.313,0.198 10 false VC 1.781,0.813 2.094,1.01 0.313,0.198 10 false 3 1.385,1.615 1.875,1.813 0.49,0.198 10 false PEX 1.49,2.385 1.802,2.583 0.313,0.198 10 false E2 1.802,2.271 2.115,2.469 0.313,0.198 10 false 1 1.792,1.51 2.104,1.708 0.313,0.198 10 false 2 5.385,3.021 5.885,3.219 0.5,0.198 10 false C39 5.385,3.229 5.906,3.427 0.521,0.198 10 false ECM 4.677,0.802 5.271,1 0.594,0.198 10 false VC 4.667,1.5 5.156,1.698 0.49,0.198 10 false PEX 4.688,2.271 5.229,2.49 0.542,0.219 10 false E2 4.406,0.802 4.719,1 0.313,0.198 10 false 91 4.406,1.5 4.719,1.698 0.313,0.198 10 false 69 4.417,2.271 4.729,2.469 0.313,0.198 10 false 92

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR ASSEMBLY)
a.

Disconnect the differential pressure sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C128-3 (VC) - C39-91 (VC) Always Below 1 Ω
C128-2 (PEX) - C39-69 (PEX) Always Below 1 Ω
C128-1 (E2) - C39-92 (E2) Always Below 1 Ω
C128-3 (VC) or C39-91 (VC) - Body ground Always 10 kΩ or higher
C128-2 (PEX) or C39-69 (PEX) - Body ground Always 10 kΩ or higher



d.

Reconnect the differential pressure sensor assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR ASSEMBLY)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR ASSEMBLY)
a.
A204467C31
0.365,1.063 0.802,1.323 0.438,0.26 1.969,1.24 2.406,1.656 true 1.479,1.271 1.188,1.656 true 0.333,0.25 0.583,0.406 0.25,0.156 10 false *a 2.406,1.656 2.667,1.823 0.26,0.167 10 false VC 0.438,1.115 0.865,1.281 0.427,0.167 10 false C108 1.01,1.656 1.271,1.823 0.26,0.167 10 false E2
*a Front view of wire harness connector
(to Differential Pressure Sensor Assembly)


Disconnect the differential pressure sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C128-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for 30 seconds.


f.

Turn the ignition switch to ON and wait for 5 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

i.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED