Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) › 2016.08–2019.09
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0137074 FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  INSTALLATION  


PROCEDURE

Hide 41110F 1.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

a.

Clean the contact surfaces of the front differential carrier and the front axle housing.


b.
C400768

Install a new gasket and the differential carrier with the 11 nuts and 11 washers.

Torque:
Nut Type A : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Nut Type B : 29.2 N*m (298 kgf*cm, 22 ft.*lbf)

NOTICE:

Be careful not to damage the installation surface.


HINT:
·

Remove any foreign matter (dirt, gasket remains, metal particles, etc.) from the contact surfaces of the housing and differential carrier and install a new gasket.

·
C400713C01
0.521,0.594 0.833,0.75 0.313,0.156 10 false *A 1.688,0.594 2,0.75 0.313,0.156 10 false *B
*A Nut Type A
*B Nut Type B


As there are 2 types of nuts, the same type nut must be used during removal and installation.




Hide 3.INSTALL FRONT AXLE SHAFT ASSEMBLY

Hide 4.INSTALL FRONT BRAKE TUBE (w/o ABS)

a.

for 1HZ, 1VD-FTV:

C311253C01
1.385,1.021 1.698,1.219 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


i.

Install the brake tube, 3-way joint and brake hose with the 4 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


ii.

Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




iii.

Install the brake tube with a new clip.



b.

for 1GR-FE:

C311254C01
1.406,1.135 1.719,1.333 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


i.

Install the brake tube, 3-way joint and brake hose with the 4 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


ii.

Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




iii.

Install the brake tube with a new clip.



Hide 5.INSTALL FRONT BRAKE TUBE (w/ ABS,VSC)

a.

for 1HZ, 1VD-FTV:

C311255C01
1.396,1.135 1.708,1.333 0.313,0.198 10 false *a 1.271,1.594 1.583,1.792 0.313,0.198 10 true A 3.323,1.854 3.635,2.052 0.313,0.198 10 true A 6.073,1.531 6.229,1.719 0.156,0.188 10 true A 4.594,0.781 4.75,0.969 0.156,0.188 10 true B
*a Torque Wrench Fulcrum Length - -


i.

Install the brake tube with the 5 bolts.

Torque:
Bolt A : 14 N*m (143 kgf*cm, 10 ft.*lbf)
Bolt B : 25 N*m (255 kgf*cm, 18 ft.*lbf)


ii.

Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




iii.

Install the brake tube with 2 new clips.



b.

for 1GR-FE:

C311256C01
5.594,1.208 5.906,1.406 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length - -


i.

Install the brake tube with the 3 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


ii.

Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)





Hide 37140 6.INSTALL FRONT PROPELLER SHAFT ASSEMBLY