| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1507 | Open in Turn Signal Circuit | Open in turn signal light circuit. |
·
Harness or connector
·
Front turn signal light socket
·
Side turn signal light socket and wire
·
Rear combination light socket and wire sub-assembly
·
Combination meter assembly |
○ |
| B1508 | Short in Turn Signal / Hazard Flasher Circuit | Short in turn signal light circuit or hazard warning light circuit. |
·
Harness or connector
·
Front turn signal light socket
·
Side turn signal light socket and wire
·
Rear combination light socket and wire sub-assembly
·
Combination meter assembly |
○ |
Inspect the bulbs for circuits related to this system before performing the following procedure.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1507 and B1508 are not output | A |
| B1507 is output | B |
| B1508 is output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Check the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| LH side turn signal light does not illuminate. | A |
| RH side turn signal light does not illuminate. | B |
A
B
*1: except Pickup
*2: for Pickup
Disconnect the L50 combination meter assembly connector.
Disconnect the A3 front turn signal light socket LH connector.
Disconnect the A11 side turn signal light socket and wire LH connector.
Disconnect the T7*1 or T5*1, or T17*2 rear combination light socket and wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-6 (LL) - A3-2 (B) | Always | Below 1 Ω |
| L50-6 (LL) - A11-2 | Always | Below 1 Ω |
| L50-6 (LL) - T7-3 (TRN)*1 | Always | Below 1 Ω |
| L50-6 (LL) - T5-2 (TRN)*1 | Always | Below 1 Ω |
| L50-6 (LL) - T17-3 (TRN)*2 | Always | Below 1 Ω |
| A3-1 (E) - Body ground | Always | Below 1 Ω |
| A11-1 - Body ground | Always | Below 1 Ω |
| T7-1 (TE) - Body ground*1 | Always | Below 1 Ω |
| T5-5 (E) - Body ground*1 | Always | Below 1 Ω |
| T17-2 (E) - Body ground*2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front turn signal light socket LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 (B) Battery negative (-) → Terminal 1 (E) |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light socket and wire LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear combination light socket and wire sub-assembly LH.
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 3 (TRN)*1 Battery negative (-) → Terminal 1 (TE)*1 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 2 (TRN)*2 Battery negative (-) → Terminal 5 (E)*2 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 3 (TRN)*3 Battery negative (-) → Terminal 2 (E)*3 |
Turn signal light illuminates |
*1: for T7 connector
*2: for T5 connector
*3: for T17 connector
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
*1: except Pickup
*2: for Pickup
Disconnect the L50 combination meter assembly connector.
Disconnect the I38 front turn signal light socket RH connector.
Disconnect the I25 side turn signal light socket and wire RH connector.
Disconnect the T6*1 or T1*1, or T14*2 rear combination light socket and wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-4 (LR) - I38-2 (B) | Always | Below 1 Ω |
| L50-4 (LR) - I25-2 | Always | Below 1 Ω |
| L50-4 (LR) - T6-3 (TRN)*1 | Always | Below 1 Ω |
| L50-4 (LR) - T1-2 (TRN)*1 | Always | Below 1 Ω |
| L50-4 (LR) - T14-3 (TRN)*2 | Always | Below 1 Ω |
| I38-1 (E) - Body ground | Always | Below 1 Ω |
| I25-1 - Body ground | Always | Below 1 Ω |
| T6-1 (TE) - Body ground*1 | Always | Below 1 Ω |
| T1-5 (E) - Body ground*1 | Always | Below 1 Ω |
| T14-2 (E) - Body ground*2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front turn signal light socket RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 (B) Battery negative (-) → Terminal 1 (E) |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light socket and wire RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 |
Turn signal light illuminates |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear combination light socket and wire sub-assembly RH.
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
Apply battery voltage to the connector and check the light illumination condition.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 3 (TRN)*1 Battery negative (-) → Terminal 1 (TE)*1 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 2 (TRN)*2 Battery negative (-) → Terminal 5 (E)*2 |
Turn signal light illuminates |
| Battery positive (+) → Terminal 3 (TRN)*3 Battery negative (-) → Terminal 2 (E)*3 |
Turn signal light illuminates |
*1: for T6 connector
*2: for T1 connector
*3: for T14 connector
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
Check the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| LH side turn signal light does not illuminate. | A |
| RH side turn signal light does not illuminate. | B |
A
B
*1: except Pickup
*2: for Pickup
Disconnect the L50 combination meter assembly connector.
Disconnect the A3 front turn signal light socket LH connector.
Disconnect the A11 side turn signal light socket and wire LH connector.
Disconnect the T7*1 or T5*1, or T17*2 rear combination light socket and wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-6 (LL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A3 front turn signal light socket LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light LH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
Disconnect the A11 side turn signal light socket and wire LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light LH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
*1: except Pickup
*2: for Pickup
Disconnect the T7*1 or T5*1, or T17*2 rear combination light socket and wire sub-assembly LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light LH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
for Canvas Top: Click here
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY
*1: except Pickup
*2: for Pickup
Disconnect the L50 combination meter assembly connector.
Disconnect the I38 front turn signal light socket RH connector.
Disconnect the I25 side turn signal light socket and wire RH connector.
Disconnect the T6*1 or T1*1, or T14*2 rear combination light socket and wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L50-4 (LR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I38 front turn signal light socket RH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light RH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
Disconnect the I25 side turn signal light socket and wire RH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light RH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
*1: except Pickup
*2: for Pickup
Disconnect the T6*1 or T1*1, or T14*2 rear combination light socket and wire sub-assembly LH connector.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Turn on the turn signal light RH and check that DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| B1508 is output | A |
| B1507 is output | B |
A
B
for Canvas Top: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Canvas Top)>DISASSEMBLY
for Pickup: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Pickup)>DISASSEMBLY
for Van: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY(for Van)>DISASSEMBLY