Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › EXHAUST PIPE (for 5 Door) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029894 1VD-FTV INTAKE / EXHAUST _0136511 EXHAUST PIPE(for 5 Door) A

1VD-FTV INTAKE / EXHAUST  EXHAUST PIPE(for 5 Door)  INSTALLATION  


PROCEDURE

Hide 18431 1.INSTALL UPPER CATALYTIC CONVERTER INSULATOR (w/o DPF)

a.

Install the upper catalytic converter insulator with the 2 bolts and nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 18450A 2.INSTALL MONOLITHIC CONVERTER ASSEMBLY (w/o DPF)

a.

Temporarily install a new gasket to the monolithic converter assembly by hand.

HINT:

Be sure to install the gasket evenly and as much as possible.



b.
A104635C26
2.625,1.063 2.958,1.063 true 1.49,1.792 1.656,1.792 1.656,1.792 2.115,1.448 false 3.01,0.948 3.219,1.156 0.208,0.208 10 false *a 1.271,1.688 1.49,1.865 0.219,0.177 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap the gasket onto the monolithic converter assembly so that the gasket is flush with the pipe end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the exhaust pipe when connecting it.




c.
A162138

Install a new gasket onto the outlet turbine elbow.


d.
A166035

Loosely install the monolithic converter assembly with 3 new nuts.

HINT:

Tighten the nuts until the contact surface of the monolithic converter assembly contacts with the outlet turbine elbow.



e.

Loosely install the center converter protector stay with the 3 bolts.

HINT:

Tighten the bolts so that the position of the monolithic converter assembly can be adjusted in a later step.



f.

Tighten the monolithic converter's nuts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


g.

Tighten the converter protector stay's bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o DPF)

a.
A104634

Inspect the compression spring.

i.

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

43 mm (1.69 in.)


If the free length is not as specified, replace the compression spring.



b.

Install the exhaust pipe support cushion to the front exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Temporarily install the front exhaust pipe assembly with the 2 bolts and 2 compression springs labeled A, and the 2 nuts labeled B.

A162134N01
1.573,2.604 1.74,2.771 0.167,0.167 10 true A 2.031,2.375 2.198,2.542 0.167,0.167 10 true A 5.302,2.281 5.448,2.458 0.146,0.177 10 true B 5.521,2.177 5.677,2.365 0.156,0.188 10 true B


d.

Tighten the bolts labeled A.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·
A162131C02
0.958,2.052 1.188,2.25 0.229,0.198 10 false *a 2.125,2.073 2.354,2.271 0.229,0.198 10 false *b
*a CORRECT
*b INCORRECT



·

When tightening the bolts, make sure the lengths of the springs are approximately the same.

·

Make sure the joint part is movable.

·

Make sure the bolts do not get caught on the flange.




e.

Tighten the nuts labeled B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ DPF)

a.

Temporarily install a new gasket to the front exhaust pipe assembly by hand.

HINT:

Be sure to install the gasket as evenly as possible.



b.
A104635C27
2.583,0.948 2.927,0.948 true 1.49,0.365 1.667,0.365 1.667,0.365 2.167,0.625 true 2.969,0.844 3.188,1.042 0.219,0.198 10 false *a 1.281,0.26 1.49,0.448 0.208,0.188 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap the gasket onto the front exhaust pipe assembly so that the gasket is flush with the pipe end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the exhaust pipe when connecting it.




c.
A162138

Install a new gasket onto the outlet turbine elbow.


d.
A391805

Loosely install the front exhaust pipe assembly with 3 new nuts.

HINT:

Tighten the nuts until the contact surface of the front exhaust pipe assembly contacts with the outlet turbine elbow.



e.
A391800

Loosely install the front exhaust pipe assembly to the No. 1 exhaust pipe support with the 4 bolts.

HINT:

Tighten the bolts so that the position of the front exhaust pipe assembly can be adjusted in a later step.




g.
A391802

Loosely install the front exhaust pipe assembly to the No. 2 frame crossmember sub-assembly with the 2 bolts.

HINT:

Tighten the bolts so that the position of the front exhaust pipe assembly can be adjusted in a later step.



h.

Tighten the 3 nuts of the front exhaust pipe assembly.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


i.

Tighten the 4 bolts of the front exhaust pipe assembly to the No. 1 exhaust pipe support.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


j.

Tighten the 2 bolts of the front exhaust pipe assembly to the No. 2 frame crossmember sub-assembly.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


k.
A391801

Connect the 2 air hoses to the front exhaust pipe assembly with 2 new clips.

NOTICE:
·

Align the paint marks of the front exhaust pipe assembly and air hose and push on the air hose until it contacts the stopper.

·

Make sure that there is no slack in the air hose, and that it is not twisted or bent.

·

Take care not to damage the inner or outer surface of the air hose when installing it. If the air hose is damaged, replace it with a new one.




Hide 89425B 5.INSTALL NO. 3 EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 89425A 6.INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 17402 7.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY (w/ DPF)

a.
A104634

Inspect the compression spring.

i.

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

43 mm (1.69 in.)


If the free length is not as specified, replace the compression spring.



b.

Install the exhaust pipe support cushion to the front No. 2 exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Temporarily install the front No. 2 exhaust pipe assembly with the 2 bolts and 2 compression springs labeled A, and the 2 nuts labeled B.

A392045N01
0.49,2.406 0.646,2.604 0.156,0.198 10 true A 1.229,2.083 1.385,2.281 0.156,0.198 10 true A 4.26,2.365 4.438,2.563 0.177,0.198 10 true B 4.646,2.115 4.823,2.313 0.177,0.198 10 true B


d.

Tighten the bolts labeled A.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·
A392052C02
0.958,2.125 1.271,2.281 0.313,0.156 10 false *a 2.177,2.146 2.49,2.302 0.313,0.156 10 false *b
*a CORRECT
*b INCORRECT



·

When tightening the bolts, make sure the lengths of the springs are approximately the same.

·

Make sure the joint part is movable.

·

Make sure the bolts do not get caught on the flange.




e.

Tighten the nuts labeled B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17430 9.INSTALL TAILPIPE ASSEMBLY

a.
A328277

Install a new gasket onto the front exhaust pipe assembly.


b.

Install the 2 exhaust pipe support cushions to the tailpipe assembly with the 4 nuts.


c.

Temporarily install the tailpipe assembly with 2 new bolts and 2 new nuts labeled A, and the 4 nuts labeled B

A162133N01
1.125,2.469 1.271,2.656 0.146,0.188 10 true A 1.771,1.75 1.938,1.948 0.167,0.198 10 true A 3.51,2.198 3.677,2.406 0.167,0.208 10 true B 3.802,2.281 3.958,2.479 0.156,0.198 10 true B 5.646,2.229 5.802,2.427 0.156,0.198 10 false B 5.958,2.156 6.125,2.344 0.167,0.188 10 true B


d.

Tighten the nuts labeled B

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Tighten the bolts and nuts labeled A.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)