1.INSTALL STUD BOLT
Using an E10 "TORX" socket wrench, install the 6 stud bolts to the turbocharger sub-assembly.
17274 2.INSTALL INLET COMPRESSOR ELBOW
Install a new gasket and the inlet compressor elbow to the turbocharger sub-assembly with the 2 bolts.
15481 3.INSTALL NO. 1 TURBO OIL PIPE
Install a new gasket and the No. 1 turbo oil pipe to the turbocharger sub-assembly with the 2 bolts.
Install the gasket with the gasket's claws facing the No. 1 turbo oil pipe.
15407 4.INSTALL INLET TURBO OIL PIPE SUB-ASSEMBLY
| *1 | Union Bolt |
Install a new gasket and the union bolt.
Install the inlet turbo oil pipe sub-assembly to the turbocharger sub-assembly with the bolt.
17141 5.INSTALL EXHAUST MANIFOLD RH
|
Front |
Install a new gasket to the cylinder head sub-assembly RH.
| *a | Colored Side |
Install the exhaust manifold RH and 10 collars with 10 new nuts.
Install the collars with the collars' colored side facing the nuts.
17142 6.INSTALL EXHAUST MANIFOLD LH
Install a new gasket and the turbocharger sub-assembly to the exhaust manifold LH with 3 new nuts.
|
Front |
Set a new gasket to the cylinder head sub-assembly LH.
| *a | Colored Side |
Install the exhaust manifold LH with turbocharger sub-assembly with 10 new nuts and the 10 collars.
Install the collars with the collars' colored side facing the nuts.
17192 7.INSTALL NO. 2 EXHAUST MANIFOLD PIPE
| *a | Gasket Claw |
Install 2 new gaskets to the No. 2 exhaust manifold pipe.
The gasket claws should face the No. 2 exhaust manifold pipe.
Install the No. 2 exhaust manifold pipe to the exhaust manifold LH with 2 nuts and 2 bolts.
17293 8.INSTALL TURBOCHARGER STAY
17106 9.INSTALL EXHAUST CROSSOVER PIPE SUB-ASSEMBLY
Temporarily install the No. 1 and No. 2 manifold stays to the exhaust crossover pipe sub-assembly with the 2 bolts labeled A and E shown in the illustration.
Make sure the manifold stays and exhaust crossover pipe sub-assembly are contacting each other.
Install a new gasket to the exhaust manifold RH and a new gasket to the exhaust manifold LH.
Temporarily install the exhaust crossover pipe sub-assembly with the bolt labeled B, 6 nuts labeled C, and 2 bolts labeled D.
Make sure to tighten the nuts labeled C so that the exhaust crossover pipe sub-assembly and exhaust manifold are contacting each other.
Tighten the bolt labeled B.
Tighten the bolts labeled D.
Tighten the nuts labeled C.
Tighten the bolt labeled A.
Tighten the bolt labeled E.
10.CONNECT MANUAL TRANSMISSION WITH TRANSFER
12101 11.CHECK OIL PAN SUB-ASSEMBLY
12101 12.INSTALL OIL PAN SUB-ASSEMBLY
13.INSTALL OIL FILTER ELEMENT
15614 14.INSTALL LOWER OIL FILTER ELEMENT COVER
12102A 15.CHECK NO. 2 OIL PAN SUB-ASSEMBLY
12102A 16.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
12140 17.INSTALL OIL PAN COVER
12201 18.INSTALL VENTILATION TUBE SUB-ASSEMBLY
25708 19.INSTALL NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
15474A 20.INSTALL OUTLET TURBO OIL HOSE
21.INSTALL ENGINE WIRE BRACKET
83520 22.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY
15407 23.CONNECT INLET TURBO OIL PIPE SUB-ASSEMBLY
15769 24.CONNECT OIL COOLER PIPE
25.CONNECT ENGINE WIRE
16027 26.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
Install a new gasket and the No. 1 turbo water pipe sub-assembly to the turbocharger sub-assembly with 2 new nuts.
Install the bolt.
Connect the No. 2 turbo water hose from the No. 1 turbo water pipe sub-assembly, and slide the clip to secure the hose.
Install the bolt.
Connect the No. 1 turbo water hose from the No. 1 turbo water pipe sub-assembly, and slide the clip to secure the hose.
17361J 27.INSTALL NO. 1 AIR TUBE
Install a new gasket and the No. 1 air tube with the 2 bolts.
Install the gasket with the gasket's claws facing the turbocharger sub-assembly.
17343D 28.INSTALL NO. 3 AIR HOSE
| *a | Upper |
Install the No. 3 air hose to the turbocharger sub-assembly with the clamp.
Install the clamp as shown in the illustration.
17362B 29.INSTALL NO. 2 AIR TUBE
| *a | Upper |
Connect the No. 2 air tube to the No. 3 air hose with the 2 clamps.
Install the clamp as shown in the illustration.
Install the No. 2 air tube with the bolt.
17878 30.INSTALL NO. 3 INTAKE AIR CONNECTOR PIPE
16620D 31.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
16603B 32.INSTALL IDLER PULLEY SUB-ASSEMBLY
15778 33.CONNECT NO. 2 OIL COOLER HOSE
27020 34.INSTALL GENERATOR ASSEMBLY
27280 35.INSTALL GENERATOR SPLASH GUARD COVER ASSEMBLY
16400 36.INSTALL RADIATOR ASSEMBLY
16572D 37.CONNECT NO. 2 RADIATOR HOSE
16371 38.INSTALL FAN PULLEY
16711 39.INSTALL FAN SHROUD
16470 40.INSTALL RADIATOR RESERVOIR ASSEMBLY
16361A 41.INSTALL FAN AND GENERATOR V-RIBBED BELT
17875 42.INSTALL INTAKE AIR CONNECTOR PIPE
43.INSTALL INTAKE AIR CONNECTOR ASSEMBLY
44.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17705 45.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
Attach the 4 clamps to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.
17881 46.INSTALL NO. 1 AIR CLEANER HOSE
17167 47.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 1 exhaust manifold heat insulator with the 3 bolts.
17168 48.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 2 exhaust manifold heat insulator with the 3 bolts.
w/ Air Conditioning System:
Install the No. 1 fuel tube bracket with the 2 bolts.
Attach the clamp.
Install the fuel tube bracket with the bolt.
Attach the engine wire.
49.INSTALL TUBE SUB-ASSEMBLY (w/ Air Conditioning System)
16571C 50.INSTALL NO. 1 RADIATOR HOSE
51.INSTALL HEATER WATER VALVE ASSEMBLY
17940D 52.INSTALL INTERCOOLER ASSEMBLY
17341F 53.INSTALL NO. 1 AIR HOSE
87249B 54.CONNECT OUTLET HEATER WATER PIPE B
17410 55.INSTALL FRONT EXHAUST PIPE ASSEMBLY
Temporarily install a new gasket to the front exhaust pipe assembly by hand.
Be sure to install the gasket as evenly as possible.
| *1 | Gasket |
| *a | Wooden Block |
Using a plastic-faced hammer and wooden block, tap the gasket onto the front exhaust pipe assembly so that the gasket is flush with the pipe end.
Install the gasket in the correct direction.
Do not damage the outer surface of the gasket.
Do not reuse the gasket.
Do not push in the gasket with the exhaust pipe when connecting it.
Install a new gasket onto the outlet turbine elbow.
Loosely install the front exhaust pipe assembly with 3 new nuts.
Tighten the nuts until the contact surface of the front exhaust pipe assembly contacts with the outlet turbine elbow.
for Single Cab:
Install the No. 2 frame crossmember sub-assembly with the 4 bolts and 6 nuts.
Click hereDrivetrain>H152F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSMISSION ASSEMBLY>INSTALLATION
Attach the clamp and connect the exhaust gas temperature sensor connector.
Loosely install the front exhaust pipe assembly to the No. 1 exhaust pipe support with the 4 bolts.
Tighten the bolts so that the position of the front exhaust pipe assembly can be adjusted in a later step.
Loosely install the front exhaust pipe assembly to the No. 2 frame crossmember sub-assembly with the 2 bolts.
Tighten the bolts so that the position of the front exhaust pipe assembly can be adjusted in a later step.
Tighten the 3 nuts of the front exhaust pipe assembly.
Tighten the 4 bolts of the front exhaust pipe assembly to the No. 1 exhaust pipe support.
Tighten the 2 bolts of the front exhaust pipe assembly to the No. 2 frame crossmember sub-assembly.
| *a | Tape |
Attach the clamp and connect the No. 3 exhaust gas temperature sensor connector.
Make sure that the tape is in the position shown in the illustration.
| *a | Tape |
Attach the clamp and connect the No. 2 exhaust gas temperature sensor connector.
Make sure that the tape is in the position shown in the illustration.
Connect the 2 air hoses to the front exhaust pipe assembly with 2 new clips.
Align the paint marks of the front exhaust pipe assembly and air hose and push on the air hose until it contacts the stopper.
Make sure that there is no slack in the air hose, and that it is not twisted or bent.
Take care not to damage the inner or outer surface of the air hose when installing it. If the air hose is damaged, replace it with a new one.
17402 56.INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY
Inspect the compression spring.
Using a vernier caliper, measure the free length of the compression spring.
43 mm (1.69 in.)
If the free length is not as specified, replace the compression spring.
| *a | CORRECT |
| *b | INCORRECT |
Connect the front No. 2 exhaust pipe sub-assembly to the front exhaust pipe assembly with the 2 bolts and 2 compression springs.
When tightening the bolts, make sure the lengths of the springs are approximately the same.
Make sure the joint part is movable.
Make sure the bolts do not get caught on the flange.
Install a new gasket onto the front No. 2 exhaust pipe sub-assembly.
for Long Wheelbase, Semi-long Wheelbase:
Install the front No. 2 exhaust pipe sub-assembly with 2 new bolts and 2 new nuts.
for Super Long Wheelbase:
Install the front No. 2 exhaust pipe sub-assembly with 2 new nuts.
Connect the air fuel ratio sensor connector.
except Long Wheelbase:
Install the 2 nuts to the exhaust pipe support cushion.
11452 57.INSTALL NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE
12142 58.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
59.INSTALL ENGINE OIL LEVEL DIPSTICK
60.ADD ENGINE OIL
61.ADD ENGINE COOLANT
62.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
63.INSPECT FOR OIL LEAK
64.INSPECT FOR COOLANT LEAK
65. CHECK ENGINE OIL LEVEL
66.INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
51442 67.INSTALL NO. 2 ENGINE UNDER COVER
53737B 68.INSTALL FRONT FENDER APRON SEAL LH
Install the front fender apron seal LH with the 11 clips.
53736 69.INSTALL FRONT FENDER APRON SEAL RH
Install the front fender apron seal RH with the 11 clips.
70.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
71.WARM UP ENGINE
72.CHECK FOR REFRIGERANT GAS LEAK