Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2016.08–2017.01
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132955 ENGINE ASSEMBLY A

1VD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53301 3.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer hose.


b.

Remove the 4 bolts and hood sub-assembly.


Hide 16400 4.REMOVE RADIATOR ASSEMBLY

Hide 17940D 5.REMOVE INTERCOOLER ASSEMBLY

Hide 87246A 8.DISCONNECT HEATER WATER HOSE

a.
A163847C01
0.365,0.167 1.365,0.167 true 1.833,0.333 2.25,0.667 2.25,0.667 2.417,0.667 true 0.208,0.073 0.417,0.271 0.208,0.198 10 false *1 2.438,0.583 2.844,0.854 0.406,0.271 10 true *2
*1 Inlet Heater Water Hose
*2 Outlet Heater Water Hose


Slide the clamp and disconnect the inlet heater water hose from the outlet heater water pipe B.


b.

Slide the clamp and disconnect the outlet heater water hose from the outlet heater water pipe B.


Hide 28800 10.REMOVE BATTERY

a.

Remove the bolt, nut, battery clamp and battery.


Hide 74403A 11.REMOVE BATTERY CARRIER SUB-ASSEMBLY

a.
A316775

Remove the bolt.


b.

Detach the clamp and disconnect the No. 2 fuse block from the battery carrier sub-assembly.


c.

Remove the fusible link block cover.


d.
A316776

Remove the bolt and disconnect the engine wire.


e.

Detach the wire harness clamp.


f.

Remove the 2 bolts.


g.

Detach the clamp and disconnect the fusible link block from the battery carrier sub-assembly.


h.
A316777

Detach the 3 wire harness clamps.


i.

Remove the 5 bolts and battery carrier sub-assembly.


Hide 44310 12.DISCONNECT VANE PUMP ASSEMBLY

a.
A328671

Disconnect the power steering oil pressure switch connector.


b.

Remove the 2 nuts and disconnect the vane pump assembly.

HINT:

It is not necessary to completely remove the vane pump assembly. With the hoses connected to the vane pump assembly, hang the vane pump assembly on the vehicle body with a rope.



c.

Remove the O-ring from the vane pump assembly.


Hide 88320 13.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.

Disconnect the cooler compressor assembly connector.


b.
A163880

Remove the 4 bolts and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 44778 14.DISCONNECT CONNECTOR TO CHECK VALVE HOSE

a.
A391913C01
0.052,0.052 0.385,0.24 0.333,0.188 10 true *A 0.052,2.354 0.365,2.51 0.313,0.156 10 true *B
*A w/o DPF
*B w/ DPF


Slide the clamp and disconnect the connector to check valve hose from the cylinder head cover sub-assembly.


Hide 23271H 15.DISCONNECT NO. 1 AND NO. 2 FUEL HOSES

a.
A391912C01
1.948,1.5 2.146,1.083 2.146,1.083 2.344,1.083 true 2.156,1.802 2.365,2.26 2.365,2.26 2.563,2.26 true 1.438,2.802 1.656,2.802 1.656,2.802 1.802,3.094 true 2.26,3.594 2.469,3.906 2.469,3.906 2.667,3.906 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *A 0.083,2.448 0.396,2.604 0.313,0.156 10 false *B 2.583,2.125 2.896,2.302 0.313,0.177 10 true *1 2.375,0.979 2.688,1.135 0.313,0.156 10 true *2 1.177,2.708 1.49,2.865 0.313,0.156 10 true *1 2.698,3.792 3.01,3.948 0.313,0.156 10 true *2
*A w/o DPF
*B w/ DPF
*1 No. 1 Fuel Hose
*2 No. 2 Fuel Hose


Slide the clamp and disconnect the No. 1 fuel hose from the fuel filter cap assembly.


b.

Slide the clamp and disconnect the No. 2 fuel hose from the fuel pipe.


Hide 82111 16.DISCONNECT ENGINE ROOM MAIN WIRE

a.

Disconnect the ECM connector.

A394928C01
4.948,2.083 5.26,2.281 0.313,0.198 10 false *A
*A w/o DPF - -



b.

Detach the 2 engine room main wire clamps.


c.

w/o DPF:

Disconnect the 4 connectors and detach the clamp.


d.
A391443

w/ DPF:

Disconnect the 7 connectors and detach the clamp.


e.
A391584C01
2.573,1.104 2.781,0.667 true 0.813,0.813 1.083,1.313 true 1.042,0.635 1.229,0.792 0.188,0.156 10 true *a 0.708,0.646 0.885,0.802 0.177,0.156 10 true *b 2.427,0.469 2.74,0.625 0.313,0.156 10 false *a 2.729,0.5 2.927,0.656 0.198,0.156 10 true *b
*a Push
*b Lock


Raise the levers while pushing the locks on the levers and disconnect the connectors.


Hide 82111 21.DISCONNECT ENGINE ROOM MAIN WIRE

a.

w/ DPF:

i.
A391794

Disconnect the 6 connectors.


ii.

Disconnect the 4 fuel injector connectors.


iii.

Remove the 5 bolts.


iv.

Detach the 2 clamps and disconnect the engine wire.


v.
A391795

Disconnect the 6 connectors.


vi.

Disconnect the 4 fuel injector connectors.


vii.

Remove the 3 bolts.


viii.

Detach the 2 clamps and disconnect the engine wire.


ix.
A391900

Remove the 2 bolts and disconnect the 2 ground wires.


x.

Detach the 2 clamps and disconnect the 2 connectors.


xi.
A391899

Detach the 2 clamps and disconnect the engine wire.


xii.
A391898

Remove the 2 bolts and disconnect the 2 wire harness clamps and 2 connectors.



b.

w/o DPF:

i.

Detach the 12 engine room main wire harness clamps.


ii.

Disconnect the 20 connectors.


iii.

Remove the 19 bolts.


iv.

Remove the terminal cap and nut, and disconnect the generator wire.

A316779



Hide 26100G 22.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

Hide 26100G 23.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 16264 26.DISCONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES (w/o DPF)

Hide 23804D 28.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

Hide 25850 33.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 16278 35.REMOVE NO. 2 WATER BY-PASS PIPE (w/o DPF)

Hide 23764A 37.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

a.
A267230

Disconnect the fuel hose.


b.

Remove the fuel check valve, No. 4 nozzle leakage pipe and gasket.


Hide 23805B 41.REMOVE NO. 5 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

Hide 23765 45.REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23801L 47.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 25800 48.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ DPF)

Hide 27148B 50.REMOVE CONNECTING WIRE (w/ DPF)

a.
A267236

Detach the 2 clamps and remove the connecting wire.


Hide 23763 51.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 16289 54.DISCONNECT NO. 5 WATER BY-PASS PIPE (w/o DPF)

Hide 25601 55.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

Hide 25602 56.REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY (w/o DPF)

Hide 25680 57.REMOVE EGR COOLER ASSEMBLY WITH NO. 2 EGR VALVE ASSEMBLY (w/ DPF)

Hide 25620 58.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER ASSEMBLY (w/o DPF)

Hide 23764A 59.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

Hide 23763 60.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

a.
A168390

Remove the union bolt and gasket.


b.

Remove the bolt and disconnect the No. 3 nozzle leakage pipe.


Hide 23901H 61.REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)

Hide 23762B 62.REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23761A 63.REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23881D 64.REMOVE FUEL HOSE BRACKET (w/ DPF)

a.
A267240

Remove the bolt and fuel hose bracket.


Hide 23841C 65.REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)

Hide 16268 66.REMOVE NO. 1 WATER BY-PASS PIPE (w/ DPF)

Hide 67.REMOVE STARTER HOSE BRACKET SUB-ASSEMBLY

a.
A287055

Disconnect the 2 starter hoses from the starter assembly and starter hose bracket sub-assembly.


b.
A272101

Remove the 2 bolts and starter hose bracket sub-assembly.


Hide 19871 70.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 82112 71.REMOVE NO. 2 ENGINE ROOM WIRE

a.
A328672

Disconnect the starter assembly connector.


b.

Remove the nut and disconnect the starter assembly wire harness.


c.

Detach the No. 2 engine room wire clamp.


d.

Remove the bolt and No. 2 engine room wire.


Hide 37140 72.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 73.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 12281A 75.INSTALL ENGINE HANGER

a.

Install the No. 1 and No. 2 engine hangers with the 4 bolts shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:
Part No.
No. 1 Engine Hanger 12281-51040
No. 2 Engine Hanger 12282-51040
Bolt 91671-80825


A316809C01
5.333,0.833 5.75,0.5 5.75,0.5 5.917,0.5 true 5.083,2.25 5.667,1.75 5.667,1.75 5.833,1.75 true 3.823,0.448 4.135,0.604 0.313,0.156 10 false *A 3.823,1.781 4.135,1.938 0.313,0.156 10 false *B 5.948,0.417 6.26,0.573 0.313,0.156 10 false *1 5.865,1.656 6.177,1.813 0.313,0.156 10 false *2
*A for Bank 1 *B for Bank 2
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger



Hide 76.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A163874C01
0.177,0.281 0.583,0.531 0.406,0.25 10 true *A 1.844,0.281 2.25,0.531 0.406,0.25 10 true *B
*A for Bank 1
*B for Bank 2


Remove the 2 nuts and 2 plate washers from the front engine mounting insulator LH and RH.


c.

Lift the engine assembly out of the vehicle carefully.

NOTICE:

Make sure the engine assembly is clear of all wiring and hoses.



d.

Place the engine assembly onto a workbench.


Hide 31210 77.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 78.REMOVE CLUTCH DISC ASSEMBLY

Hide 33311W 79.INSPECT INPUT SHAFT BEARING

Hide 33311W 80.REPLACE INPUT SHAFT BEARING

Hide 13405 81.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A163869C01
0.5,4.333 0.5,3.792 true 0.75,2.125 0.75,1.583 true 1.25,3 1.917,3 true 1.958,4.146 1.958,3.604 true 1.104,2.906 1.417,3.063 0.313,0.156 10 false *1 1.875,4.125 2.188,4.281 0.313,0.156 10 false *a 0.615,2.135 1.073,2.333 0.458,0.198 10 false SST 0.365,4.344 0.823,4.542 0.458,0.198 10 false SST
*1 Crankshaft Pulley
*a Protective Tape


Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

To prevent damage to the crankshaft pulley, apply protective tape to the contact areas of SST and the crankshaft pulley before performing this procedure.



b.
A163846

Remove the 8 bolts and flywheel sub-assembly.


Hide 82.INSTALL ENGINE ASSEMBLY ON ENGINE STAND

a.

Install the engine assembly onto an engine stand with the bolts.


Hide 12281A 83.REMOVE ENGINE HANGER

a.

Remove the 4 bolts and No. 1 and No. 2 engine hangers.


Hide 12361 84.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A167781C01
0.25,0.063 0.583,0.302 0.333,0.24 10 false *A 1.99,0.063 2.302,0.219 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Remove the nut, front engine mounting insulator RH and engine mounting stabilizer.


Hide 12361 85.REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a.

Remove the nut, front engine mounting insulator LH and engine mounting stabilizer.


Hide 12371 86.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
A167784

Remove the 4 bolts and rear No. 1 engine mounting insulator from the manual transmission with transfer.