Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL INJECTOR (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029770 1VD-FTV FUEL _0290474 FUEL INJECTOR(w/ DPF) A

1VD-FTV FUEL  FUEL INJECTOR(w/ DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.

·

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION



PROCEDURE

Hide 1.INSTALL FUEL INJECTOR LH

NOTICE:
·

Be sure to install the fuel injector, holder clamp and bolt to their original positions.

·

Before installing the fuel injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head sub-assembly and fuel injector. If there is foreign matter, remove it before installing the fuel injector.



a.
A271223

Install 4 new injection nozzle seats to the cylinder head sub-assembly.


b.
A369258C01
0.906,1.042 1.615,0.844 true 0.74,0.969 0.969,1.156 0.229,0.188 10 false *a
*a Fuel Injector Seal


Install 4 new fuel injector seals to each fuel injector as shown in the illustration.


c.

Apply a light coat of clean engine oil to 4 new O-rings.


d.
A369259C01
0.844,1.354 1.646,1.115 true 0.656,1.292 0.906,1.469 0.25,0.177 10 false *a
*a O-Ring


Install the O-rings to each fuel injector as shown in the illustration.


e.

Insert the 4 injectors into the cylinder head sub-assembly.

NOTICE:
·

Insert the fuel injector until it touches the nozzle seat surface.

·

After installing the fuel injector to the cylinder head sub-assembly, the O-ring may prevent the fuel injector from fully seating. If so, pull out the fuel injector and reinstall it.

·

Always return a fuel injector to the same place it was removed from.




f.

For an fuel injector that has been replaced with a new fuel injector, register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


g.
A354209C01
2.24,2.26 2.938,2.26 false 2.438,1.813 3.146,1.813 false 2.24,1.135 2.938,1.135 false 2.958,1.031 3.146,1.188 0.188,0.156 10 false *a 3.167,1.708 3.354,1.865 0.188,0.156 10 false *b 2.969,2.156 3.156,2.313 0.188,0.156 10 false *c
*a Washer
*b Nozzle Holder Clamp
*c Nozzle Holder Seal


Temporarily install 4 new washers, 4 nozzle holder clamps and 4 new nozzle holder seals with the 4 clamp bolts.

NOTICE:
A278347C01
1.323,1.052 0.479,0.667 true 2.875,0.729 2.063,1.031 true 0.313,0.563 0.479,0.719 0.167,0.156 10 false *a 2.906,0.604 3.073,0.76 0.167,0.156 10 true *a
*a Nozzle Holder Clamp


·

The fork portion of the nozzle holder clamp must be set on the fuel injector.

·

Before tightening the bolts, check that the nozzle holder clamp is set properly.

·

To tighten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.

·

When tightening the bolts, be careful not to tilt the bolt and clamp.

·

Do not reuse the washer.




h.
A267323

Temporarily install the common rail LH with the 2 bolts.


i.
A271637

Temporarily install 4 new injection pipes to the common rail and fuel injector.


j.

Check the nozzle leakage pipe. Check there are no scratches or dents on the union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.


k.
A392186C01
0.51,1.604 0.698,1.76 0.188,0.156 10 true *a 2.135,0.656 2.333,0.813 0.198,0.156 10 true *b 1.177,1.604 1.365,1.76 0.188,0.156 10 true *a 2.688,1.583 2.875,1.74 0.188,0.156 10 true *a 2,1.604 2.188,1.76 0.188,0.156 10 true *a 3.104,0.771 3.302,0.927 0.198,0.156 10 true *b
*a Injector Hollow Screw
*b Bolt


Temporarily install the No. 2 leakage pipe and 4 new gaskets with the 4 injector hollow screws and 2 bolts.

HINT:

To position the fuel injectors, loosely tighten the 4 hollow screws and 2 bolts.



l.
A271221

Tighten the 4 holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


m.

Remove the 4 injection pipes.


n.

Remove the 2 bolts and common rail LH.


Hide 23762B 2.INSTALL NO. 2 NOZZLE LEAKAGE PIPE

a.
A392186C01
0.51,1.604 0.698,1.76 0.188,0.156 10 true *a 2.135,0.656 2.333,0.813 0.198,0.156 10 true *b 1.177,1.604 1.365,1.76 0.188,0.156 10 true *a 2.688,1.583 2.875,1.74 0.188,0.156 10 true *a 2,1.604 2.188,1.76 0.188,0.156 10 true *a 3.104,0.771 3.302,0.927 0.198,0.156 10 true *b
*a Injector Hollow Screw
*b Bolt


Tighten the 4 injector hollow screws and 2 bolts.

Torque:
for injector hollow screw : 18 N*m (184 kgf*cm, 13 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 3.INSTALL FUEL INJECTOR RH

NOTICE:
·

Be sure to install the fuel injector, holder clamp and bolt to their original positions.

·

Before installing the fuel injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head sub-assembly and fuel injector. If there is foreign matter, remove it before installing the fuel injector.



a.
A271223

Install 4 new injection nozzle seats to the cylinder head sub-assembly.


b.
A369258C01
0.906,1.042 1.615,0.844 true 0.74,0.969 0.969,1.156 0.229,0.188 10 false *a
*a Fuel Injector Seal


Install 4 new fuel injector seals to each fuel injector as shown in the illustration.


c.

Apply a light coat of clean engine oil to 4 new O-rings.


d.
A369259C01
0.844,1.354 1.646,1.115 true 0.656,1.292 0.906,1.469 0.25,0.177 10 false *a
*a O-Ring


Install the O-rings to each fuel injector as shown in the illustration.


e.

Insert the 4 fuel injectors into the cylinder head sub-assembly.

NOTICE:
·

Insert the fuel injector until it touches the nozzle seat surface.

·

After installing the fuel injector to the cylinder head sub-assembly, the O-ring may prevent the fuel injector from fully seating. If so, pull out the fuel injector and reinstall it.

·

Always return a fuel injector to the same place it was removed from.




f.

For a fuel injector that has been replaced with a new injector, register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


g.
A354209C01
2.24,2.26 2.938,2.26 false 2.438,1.813 3.146,1.813 false 2.24,1.135 2.938,1.135 false 2.958,1.031 3.146,1.188 0.188,0.156 10 false *a 3.167,1.708 3.354,1.865 0.188,0.156 10 false *b 2.969,2.156 3.156,2.313 0.188,0.156 10 false *c
*a Washer
*b Nozzle Holder Clamp
*c Nozzle Holder Seal


Temporarily install 4 new washers, 4 nozzle holder clamps and 4 new nozzle holder seals with the 4 clamp bolts.

NOTICE:
A278347C01
1.323,1.052 0.479,0.667 true 2.875,0.729 2.063,1.031 true 0.313,0.563 0.479,0.719 0.167,0.156 10 false *a 2.906,0.604 3.073,0.76 0.167,0.156 10 true *a
*a Nozzle Holder Clamp


·

The fork portion of the nozzle holder clamp must be set on the fuel injector.

·

Before tightening the bolts, check that the nozzle holder clamp is set properly.

·

To tighten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.

·

When tightening the bolts, be careful not to tilt the bolt and clamp.

·

Do not reuse the washer.




h.
A395785

Temporarily install the common rail RH with the 2 bolts.


i.
A271636

Temporarily install 4 new injection pipes to the common rail and fuel injector.


j.

Check the nozzle leakage pipe. Check that there are no scratches or dents on the union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.


k.
A392188C01
0.823,1.771 1.01,1.927 0.188,0.156 10 true *a 0.229,0.177 0.542,0.333 0.313,0.156 10 false *b 1.646,1.771 1.833,1.927 0.188,0.156 10 true *a 2.365,1.771 2.552,1.927 0.188,0.156 10 true *a 3.073,1.74 3.26,1.896 0.188,0.156 10 true *a
*a Injector Hollow Screw
*b Union Bolt


Temporarily install the No. 1 leakage pipe and 4 new gaskets with the 4 injector hollow screws and union bolt.

HINT:

To position the injectors, loosely tighten the 4 hollow screws and union bolt.



l.
A271220

Tighten the 4 holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


m.

Remove the 4 injection pipes.


n.

Remove the 2 bolts and common rail RH.


Hide 23761A 4.INSTALL NO. 1 NOZZLE LEAKAGE PIPE

a.
A392185C02
0.813,1.792 0.99,1.948 0.177,0.156 10 true *b 0.094,1.094 0.406,1.25 0.313,0.156 10 false *d 0.406,0.042 0.719,0.198 0.313,0.156 10 false *c 0.104,0.375 0.417,0.531 0.313,0.156 10 false *a 1.688,1.792 1.865,1.948 0.177,0.156 10 true *b 2.385,1.792 2.563,1.948 0.177,0.156 10 true *b 3.073,1.75 3.25,1.906 0.177,0.156 10 true *b
*a Union Bolt
*b Injector Hollow Screw
*c Check Valve
*d Bolt


Tighten the union bolt and 4 injector hollow screws.

Torque:
for union bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for injector hollow screw : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Install the fuel tube and No. 1 nozzle leakage pipe with the check valve and new gasket.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23763 5.INSTALL NO. 3 NOZZLE LEAKAGE PIPE

a.
A267237C01
0.208,0.594 0.521,0.75 0.313,0.156 10 false *a 1.219,0.208 1.417,0.365 0.198,0.156 10 true *b 3.198,0.75 3.385,0.906 0.188,0.156 10 false *a 2.167,0.271 2.365,0.427 0.198,0.156 10 true *b 0.198,1.688 0.396,1.844 0.198,0.156 10 true *b
*a Injector Hollow Screw
*b Bolt


Temporarily install 2 new gaskets and the No. 3 nozzle leakage pipe with the 2 injector hollow screws and 3 bolts.


b.

Tighten the 2 injector hollow screws and 3 bolts.

Torque:
for injector hollow screw : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt : 21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tighten the injector hollow screws first, and then tighten the bolts.



Hide 27148B 6.INSTALL CONNECTING WIRE

a.

Attach the 2 clamps to install the connecting wire.


Hide 23801L 8.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 17940D 10.INSTALL INTERCOOLER ASSEMBLY

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL