Home › Engine / Hybrid System › 1VD-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029525 1VD-FTV EMISSION CONTROL _0290812 EMISSION CONTROL SYSTEM(w/ DPF) G

1VD-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM(w/ DPF)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

In a malfunction where the EGR system is always on, black or white smoke may be emitted from the exhaust pipe.


PROCEDURE

Hide 1.CHECK SEATING OF EGR VALVE

a.

Start the engine, and then check that the engine starts and runs at idle.


Hide 2.CHECK ENGINE CONDITION

a.

Connect the GTS to the DLC3.


b.

Start the engine, then run it at idle.


c.

Turn the GTS on.


d.

Warm up the engine.

HINT:

The coolant temperature should be between 75°C (167°F) and 88 °C (190 °F).



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Actual EGR Valve Pos.

Powertrain > Engine and ECT > Data List
Tester Display
Actual EGR Valve Pos.
50003 61 578

f.

Check that the value of the EGR angle is within the specification.

Standard:
Engine Condition EGR Valve Opening Angle Expressed as Percentage
During idling 0 to 70%


If the result is not as specified, refer to the EGR valve inspection procedures.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/o DPF)>INSPECTION


g.

Turn the ignition switch off.


Hide 3.CHECK EGR VALVE OPERATION

a.

Turn the ignition switch to ON.


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR step position.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the EGR Step Position
50004 61 95

d.

Check the Data List / Actual EGR Valve Pos reading.

Powertrain > Engine and ECT > Data List
Tester Display
Actual EGR Valve Pos.
50003 61 578
HINT:

Make sure the EGR valve opening angle changes according to the Active Test operation.


Standard Percentage:
Control Range Condition Specified Condition
Active Test performed (Set EGR position to 100%) EGR Valve Angle: 100%
Active Test performed (Set EGR position to 0%) EGR Valve Angle: 0%


If the result is not as specified, refer to DTC P0400.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0400


Hide 4.CHECK MAF AMOUNT

a.

Start the engine, then run it at idle.


b.

Warm up the engine.

HINT:

The coolant temperature should be between 75°C (167°F) and 88°C (190°F).



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 61 319

e.

Check the MAF reading.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR valve close.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the EGR Valve Close
50004 61 183
HINT:
·

In the Active Test, the EGR valve of bank 1 and bank 2 cannot be operated at the same time.

·

In the Active Test, the change in the MAF amount is difficult to check because the EGR valve can only be operated one bank at a time. Therefore, use the value below as a reference and check that the MAF amount changes.



Standard (Reference):
Engine Condition Active Test Condition MAF Reading
Idling Active Test performed (Set EGR position to 0%) Air flow amount changes
(Approximately 6.1 to 26.5 g/sec.)



Hide 5.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.
A165481

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil dipstick, filler cap, PCV hose and other components may cause the engine to run improperly.


·

Air suction caused by disconnections, looseness or cracks in the parts of the air induction system between the throttle body and cylinder head will cause engine failure or engine malfunctions.



If the result is not as specified, replace parts as necessary.


b.
A391362

Check if the differential pressure sensor hoses are connected incorrectly, disconnected, leaking, cracked or otherwise damaged.


Hide 6.PERFORM DPF FORCIBLE REGENERATION PROCEDURE

a.

Disconnect the cable from the negative (-) battery terminal or remove the EFI MAIN fuse for 1 minute or more.

HINT:
·

If the MIL is illuminated, first clear the DTCs using the GTS, and then initialize the value for the amount of particulate matter recorded by the ECM by disconnecting the cable from the negative (-) battery terminal or removing the EFI MAIN fuse. Otherwise, forced DPF regeneration cannot be performed using the Active Test.

·

If the MIL is not illuminated, proceed to the next step, as initialization is not necessary.




b.

Connect the GTS to the DLC3.


c.

Start the engine and idle it until the engine coolant temperature reaches 70°C (158°F) or higher.


d.

Move the shift lever to N and set the parking brake.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM).

Powertrain > Engine > Active Test
Tester Display
Activate the DPF Rejuvenate (PM)
50004 61 97
A391368E01
5.646,1.448 5.813,1.448 5.813,1.448 6.031,1.26 false 2.26,2.104 2.5,1.833 2.5,1.833 2.677,1.833 false 4.135,2.583 4.375,2.313 4.375,2.313 4.552,2.313 false 3.917,1.365 5.885,1.583 1.969,0.219 10 false PM regeneration completed 0.052,1.417 2.25,1.833 2.198,0.417 10 true (Ambient temperature: 25°C (77°F)) 2.729,1.76 4.698,1.979 1.969,0.219 10 false PM regeneration started 6.552,3.385 7.063,3.615 0.51,0.229 10 false Time 4.656,2.229 6.625,2.448 1.969,0.219 10 false PM volume stored 3.531,3.188 5.5,3.406 1.969,0.219 10 false 20 minutes or more 0.302,1.156 1.042,1.365 0.74,0.208 10 false 2000 rpm 0.365,0.156 0.917,0.542 0.552,0.385 10 false Engine Speed 0.417,2.281 0.948,2.521 0.531,0.24 10 false (Idling) 6.094,2.708 6.49,2.906 0.396,0.198 10 false 12% 0.406,2.031 1.146,2.24 0.74,0.208 10 false 550 rpm

CAUTION:

Before performing the Active Test, make sure that there are no combustible materials around the DPF and tailpipe.


NOTICE:

If the ambient temperature is 30°C (86°F) or higher, the DPF and surrounding area become very hot. Use a fan, etc. to cool the exhaust gas temperature sensors, air-fuel ratio sensor and surrounding areas.


HINT:
·

The engine speed differs depending on the ambient temperature and atmospheric pressure.

·

The engine speed increases during the Active Test and the engine speed returns to idle when the Active Test is completed.

·

The time it takes to complete the Active Test varies depending on the PM volume stored. However, it usually takes approximately 20 to 40 minutes to complete the Active Test.

·

Do not cancel the Active Test unless absolutely necessary.

·

If the Active Test needs to be canceled, depress the accelerator pedal or press the DPF switch and race the engine to cancel the process.

·

If the differential pressure value increases too much during the Active Test, the fail-safe function activates and the Active Test is stopped.

·

It may not be possible to perform the Active Test when the ambient temperature is extremely low or the elevation is extremely high. In this case, perform the Active Test indoors (with the tailpipe pointed towards the outside) or drive the vehicle at a speed of approximately 60 km/h (37 mph) or more for approximately 20 minutes to perform regeneration.

·

Depending on various conditions, the Active Test may not be completed within 20 minutes. If 60 minutes elapse, the system determines that forced regeneration is impossible, stops the Active Test and illuminates the MIL. If this happens, perform troubleshooting according to the troubleshooting procedure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P244C

·

DPF forcible regeneration stops once the PM volume drops to 12 percent.

·

In either of the following cases, turn the air conditioner on and perform forced regeneration:

-

If both the atmospheric pressure (as found at low elevations) and the outside air temperature are high, the engine speed fluctuates within the range of 1600 to 2000 rpm.

-

Regeneration does not end (the engine speed does not return to the idle speed of 550 rpm) within 60 minutes.