Home › Engine / Hybrid System › 1VD-FTV (FUEL) › COMMON RAIL (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029770 1VD-FTV FUEL _0290476 COMMON RAIL(w/ DPF) A

1VD-FTV FUEL  COMMON RAIL(w/ DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.

·

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION



PROCEDURE

Hide 23820A 1.INSTALL COMMON RAIL ASSEMBLY LH

a.

Install the common rail assembly LH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23765 2.INSTALL NO. 5 NOZZLE LEAKAGE PIPE

a.
A392098C01
0.729,1.177 0.958,0.188 true 0.604,1.615 0.375,1.698 true 0.885,0.031 1.073,0.208 0.188,0.177 10 true *1 0.208,1.646 0.406,1.802 0.198,0.156 10 false *2 1.313,1.802 1.49,1.979 0.177,0.177 10 true *a 0.219,0.688 0.417,0.844 0.198,0.156 10 true *b
*1 No. 5 Nozzle Leakage Pipe
*2 No. 1 Fuel Hose
*a Clamp
*b Union Bolt


Install a new gasket and the No. 5 nozzle leakage pipe to the common rail assembly LH with the union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Make sure there is no foreign matter or damage on the seal surface.



b.

Connect the No. 1 fuel hose and slide the clamp to secure the hose.


Hide 23802B 3.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

a.
A392097C01
0.198,0.833 0.396,1 0.198,0.167 10 true *a 3.052,0.813 3.25,0.969 0.198,0.156 10 true *b 1.594,0.313 1.771,0.469 0.177,0.156 10 true *c
*a Clamp
*b Union Bolt
*c Bolt


Install a new gasket and the No. 2 fuel pipe sub-assembly to the common rail assembly LH with the union bolt and bolt.

Torque:
for union bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the fuel hose and slide the clamp to secure the hose.


Hide 23810A 4.INSTALL COMMON RAIL ASSEMBLY RH

a.

Install the common rail assembly RH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the fuel pressure sensor connector.


c.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the common rail assembly RH.

Torque:
Specified tightening torque:

34 N*m (347 kgf*cm, 25 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 29.1 N*m (297 kgf*cm, 21 ft.*lbf)




Hide 23706 5.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 17940D 7.INSTALL INTERCOOLER ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL