Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0045  Turbocharger / Supercharger Boost Control Solenoid Circuit / Open  


DESCRIPTION

The vacuum regulating valve (VRV) is controlled by the ECM with the duty control. According to the engine state, the VRV controls the vacuum applied to the actuator, which is installed to the turbocharger. If an open or short malfunction occurs in the VRV circuit, this DTC is output.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0045 Turbocharger / Supercharger Boost Control Solenoid Circuit / Open Open or short in vacuum regulating valve (VRV) circuit for 0.5 seconds or more
(1 trip detection logic)
·

Vacuum regulating valve (VRV)

·

Open or short in VRV circuit

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0045 Ignition switch ON for 1 second

WIRING DIAGRAM

A394554E02
0.438,2.073 1.51,2.271 1.073,0.198 10 false FL MAIN 0.583,0.875 1.354,1.073 0.771,0.198 10 false EFI MAIN2 1.729,1.625 2.271,1.823 0.542,0.198 10 false MAIN2 2.396,1.146 2.646,1.344 0.25,0.198 10 false 1 2.396,0.594 2.646,0.792 0.25,0.198 10 false 3 1.417,0.594 1.667,0.792 0.25,0.198 10 false 5 1.417,1.135 1.667,1.333 0.25,0.198 10 false 2 2.802,1.021 4.594,1.219 1.792,0.198 10 false Vacuum Regulating Valve 2.802,0.875 3.344,1.073 0.542,0.198 10 false C91 3.052,0.573 3.302,0.771 0.25,0.198 10 false 1 3.938,0.573 4.188,0.771 0.25,0.198 10 false 2 5.115,0.729 5.427,0.927 0.313,0.198 10 false C39 5.125,2.792 5.438,2.99 0.313,0.198 10 false C39 5.156,1.26 5.469,1.458 0.313,0.198 10 false I84 5.115,0.542 5.427,0.74 0.313,0.198 10 false 85 5.167,1.094 5.479,1.292 0.313,0.198 10 false 44 5.156,2.615 5.469,2.813 0.313,0.198 10 false 81 5.479,2.802 5.792,3 0.313,0.198 10 false E1 5.469,1.26 5.927,1.469 0.458,0.208 10 false MREL 5.469,0.604 5.927,0.813 0.458,0.208 10 false VN 5.906,3.385 6.365,3.594 0.458,0.208 10 false ECM 0.542,2.813 1.615,3.01 1.073,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT VACUUM REGULATING VALVE ASSEMBLY (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL 1 VOLTAGE)

NG

2.CHECK HARNESS AND CONNECTOR (TERMINAL 1 VOLTAGE)
a.

Disconnect the vacuum regulating valve connector.


A165725C02
1.521,0.969 1.938,1.219 0.417,0.25 1.604,1.031 1.906,1.219 0.302,0.188 10 false C91 0.167,0.125 0.375,0.292 0.208,0.167 10 false *a
*a Front view of wire harness connector
(to Vacuum Regulating Valve)


b.

Measure the voltage according to the value(s) in the table below.


Standard voltage:
Tester Connection Switch Condition Specified Condition
C91-1 - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (MAIN2 RELAY - VACUUM REGULATING VALVE)
3.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE - ECM)
a.

Disconnect the vacuum regulating valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C91-2 - C39-85 (VN) Always Below 1 Ω
C91-2 or C39-85 (VN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN2 RELAY - VACUUM REGULATING VALVE)
a.

Disconnect the VRV connector.


b.

Remove the MAIN2 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C91-1 - MAIN2 relay terminal 3 Always Below 1 Ω
C91-1 or MAIN2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR