Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  Brake Override System  


DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A308494E19
0.417,0.552 3.021,0.75 2.604,0.198 10 false Accelerator Pedal Position Sensor 0.458,1.333 2.51,2.167 2.052,0.833 10 false Master Cylinder Pressure Sensor (Brake Actuator Assembly) 0.417,2.563 3.021,2.76 2.604,0.198 10 false Stop Light Switch 0.688,3.396 2.146,3.604 1.458,0.208 10 false Vehicle Speed Sensor 5.677,2.063 6.979,3.167 1.302,1.104 10 false Effective Accelerator Pedal Angle for System Control 2.708,0.813 3.875,1.26 1.167,0.448 10 false Actual Accelerator Pedal Angle 2.833,1.771 3.833,2.292 1,0.521 10 false Master Cylinder Pressure 3.042,2.76 5.646,2.958 2.604,0.198 10 false ON/OFF 2.927,3.792 4.125,4.052 1.198,0.26 10 false Vehicle Speed 4.323,4.188 4.74,4.385 0.417,0.198 10 false ECM 0.771,3.813 2.229,4.021 1.458,0.208 10 false Wheel Speed Sensor 1.281,3.625 1.583,3.813 0.302,0.188 10 false or

Activation Conditions:

When the accelerator pedal and brake pedal are depressed.

NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



Items Controlled:
·

When the vehicle speed is extremely low, the accelerator opening value used when controlling the engine is reduced more than normal.


HINT:

During control, the Accelerator Position value in the Data List will be lower than normal.


·

When the vehicle speed is not extremely low, the accelerator opening value is forcibly lowered to a fixed value.


HINT:

During control, the Accelerator Position value in the Data List is forcibly reduced to a specified value regardless of the actual accelerator opening value (Accel Sens. No. 1 Volt %).



Deactivation Conditions:
·

When the brake pedal or the accelerator pedal returns to some degree.



CAUTION / NOTICE / HINT

Inspection Method

Example:

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving, make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DATA LIST / ACTIVE TEST

·

If the Accelerator Position and Accel Sens. No.1 Volt % values in the Data List diverge and the Accelerator Position value in the Data List is fixed even though Accel Sens. No.1 Volt % is changing, check that this control is activated (use the GTS snapshot function to record data while driving the vehicle, and then confirm it after driving is completed).



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: System Select / Health Check.


d.

Check DTCs.

Result:
Result Proceed to
No DTC is output A
DTC is output B




A

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE)

B

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Master Cylinder Pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Pressure
50003 105 393

e.

Read the value displayed on the GTS.

GTS Display Measurement Item/Range Normal Condition
Master Cylinder Pressure Master cylinder pressure sensor detected pressure/ Min.: 0.00 MPa, Max.: 23.28 MPa
·

Brake pedal released: 0.00 to 1.76 MPa

·

Reading increases when brake pedal is depressed




f.

Check that the brake fluid pressure value of the "Master Cylinder Pressure" observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the pressure displayed on the GTS increases.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

INSPECT BRAKE ACTUATOR ASSEMBLY

3.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

Powertrain > Engine and ECT > Data List
Tester Display
Stop Light Switch
50003 61 188

d.

Check the Data List indication when the brake pedal is depressed and released.

OK:
GTS Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE PEDAL

NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

4.INSPECT BRAKE PEDAL
a.

Inspect and adjust the brake pedal.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL>ADJUSTMENT

HINT:

If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE BRAKE PEDAL

5.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Accel Sens. No. 1 Volt % Accelerator Pedal
Released → Depressed → Released
Values smoothly change the following accelerator pedal operation
Accel Sens. No. 2 Volt %


HINT:

For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

6.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR