Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0627 Fuel Pump Control Circuit / Open Open or short in suction control valve circuit for more than 0.5 seconds
(1 trip detection logic)
·

Open or short in suction control valve circuit

·

Suction control valve

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored

HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and the common rail system, refer to the system description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>SYSTEM DESCRIPTION

·

When DTC P0627 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.



Reference
Engine Speed Fuel Press
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.
A168115C01
1.448,1.427 1.927,1.729 0.479,0.302 1.885,2.271 2.5,2.052 true 1.552,2.281 0.938,2.052 true 0.135,0.073 0.427,0.344 0.292,0.271 10 false *a 1.573,1.5 1.865,1.667 0.292,0.167 10 false rC1 0.531,1.969 0.875,2.167 0.344,0.198 10 false PCV 2.563,1.969 2.802,2.135 0.24,0.167 10 false +B
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
rC1-1 (PCV) - rC1-2 (+B) 20°C (68°F) 1.9 to 2.3 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE - ECM)

NG

4.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
2.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE - ECM)
a.
A311457C01
1.531,0.417 1.948,0.667 0.417,0.25 1.25,2.333 1.667,2.583 0.417,0.25 1.083,1.021 1.521,1.188 true 2.313,1.042 1.938,1.208 true 2.385,4.208 2.188,3.698 true 1.844,4.198 2.094,3.698 true 0.167,0.104 0.479,0.26 0.313,0.156 10 false *a 0.167,2.135 0.479,2.292 0.313,0.156 10 false *b 1.625,0.458 1.938,0.615 0.313,0.156 10 false rC1 1.333,2.375 1.646,2.531 0.313,0.156 10 false C39 0.833,0.927 1.146,1.083 0.313,0.156 10 false +B 2.385,0.948 2.698,1.104 0.313,0.156 10 false PCV 1.438,4.219 2.219,4.438 0.781,0.219 10 false 105 (PCV-) 2.281,4.229 3.146,4.438 0.865,0.208 10 false 106 (PCV+)
*a Front view of wire harness connector
(to Fuel Temperature Sensor, Suction Control Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
rC1-1 (PCV) - C39-105 (PCV-) Always Below 1 Ω
rC1-2 (+B) - C39-106 (PCV+) Always Below 1 Ω
rC1-1 (PCV) or C39-105 (PCV-) - Body ground Always 10 kΩ or higher
rC1-2 (+B) or C39-106 (PCV+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Clear DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Turn the ignition switch ON and wait for approximately 1 minute.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P0627 is output A
No output is output B




A

B

4.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
a.
A311458C02
1.292,3.25 1.74,3.479 false 2.521,3.25 2.115,3.49 false 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.802,0.792 1.115,0.99 0.313,0.198 10 false *b 1.229,3.563 1.542,3.76 0.313,0.198 10 false *c 0.979,3.156 1.292,3.354 0.313,0.198 10 false PCV 2.563,3.156 2.875,3.354 0.313,0.198 10 false +B
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)
*b Suction Control Valve Wire "A"
*c Fuel Temperature Sensor, Suction Control Valve Wire "B"


Remove the fuel temperature sensor, suction control valve wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
"A"-1 - "B"-2 (+B) Always Below 1 Ω
"A"-2 - "B"-1 (PCV) Always Below 1 Ω
"A"-1 or "B"-2 (+B) - Body ground Always 10 kΩ or higher
"A"-2 or "B"-1 (PCV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE