Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0100  Mass or Volume Air Flow Circuit  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow (MAF) meter uses a platinum hot wire. The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The mass air flow meter hot wire and temperature sensor (located in the intake air by-pass of the housing) detect changes in the intake air temperature.

The hot wire is maintained at the predetermined temperature by controlling the current flow through the hot wire. This current flow is then used as the output voltage of the mass air flow meter.

The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the predetermined temperature.

A160257E01
2.954,2.753 5.064,2.960 2.110,0.207 10 Temperature Sensor (Thermistor) 1.929,0.681 2.184,0.845 0.255,0.163 10 +B 1.878,1.033 2.969,1.179 1.091,0.145 10 Power Transistor 2.18,1.424 3.342,1.595 1.162,0.171 10 Hot Wire (Heater) 5.974,2.76 7.117,2.932 1.143,0.171 10 Hot Wire (Heater) 1.357,2.631 1.593,1.889 false 2.142,1.492 1.962,1.924 false 2.574,2.013 3.560,2.207 0.986,0.194 10 Output Voltage 4.646,2.733 5.424,1.969 false 6.322,2.003 6.116,2.746 false 1.323,1.911 1.487,2.075 0.164,0.165 10 A 2.133,1.904 2.299,2.072 0.165,0.168 10 B 4.967,3.273 6.151,3.439 1.184,0.165 10 Cold Film Element 0.474,2.638 1.658,2.803 1.184,0.165 10 Cold Film Element 5.507,3.235 5.794,1.968 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass or Volume Air Flow Circuit Open or short in mass air flow meter circuit for more than 3 seconds with engine speed at 4000 rpm or less
(1 trip detection logic)
·

Open or short in mass air flow (MAF) meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0102 Mass or Volume Air Flow Circuit Low Input Open in mass air flow meter circuit for more than 3 seconds with engine speed at 4000 rpm or less
(1 trip detection logic)
·

Open or short in mass air flow (MAF) meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass or Volume Air Flow Circuit High Input Short in mass air flow meter circuit for more than 3 seconds with engine speed at 4000 rpm or less
(1 trip detection logic)
·

Open or short in mass air flow (MAF) meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

After confirming DTC P0100, P0102 or P0103, check the mass air flow ratio in the "Powertrain / Engine and ECT / Data List / MAF" menu using the GTS.


Reference:
Air Flow Value (gm/sec.) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


174.0 or more Open in EVG circuit

WIRING DIAGRAM

for RHD
A225114E02
3.271,4.135 4.156,4.354 0.885,0.219 10 false MAIN 6.323,6.073 6.698,6.229 0.375,0.156 10 false ECM 1.115,3.396 2,3.615 0.885,0.219 10 false EFI MAIN 0.646,4.552 1.354,4.719 0.708,0.167 10 false FL MAIN 0.802,5.313 1.396,5.531 0.594,0.219 10 false Battery 3.906,3.906 4.052,4.073 0.146,0.167 10 false 1 2.948,3.906 3.094,4.073 0.146,0.167 10 false 2 3.906,3.344 4.052,3.51 0.146,0.167 10 false 3 2.948,3.344 3.094,3.51 0.146,0.167 10 false 5 5.729,3.625 5.927,3.792 0.198,0.167 10 false 44 5.688,3.802 5.99,3.99 0.302,0.188 10 false A29 5.729,4.156 5.927,4.323 0.198,0.167 10 false 81 5.677,4.344 5.99,4.531 0.313,0.188 10 false C39 6.042,4.344 6.479,4.51 0.438,0.167 10 false E1 6.042,3.792 6.479,3.948 0.438,0.156 10 false MREL 3.698,2.042 5.021,2.188 1.323,0.146 10 false Mass Air Flow Meter 3.698,1.906 4.01,2.063 0.313,0.156 10 false C41 3.396,1.625 3.552,1.781 0.156,0.156 10 false 1 5.135,1.552 5.292,1.708 0.156,0.156 10 false 2 5.135,1.052 5.292,1.208 0.156,0.156 10 false 3 5.677,1.25 5.948,1.406 0.271,0.156 10 false 118 5.729,0.76 5.938,0.917 0.208,0.156 10 false 72 3.583,1.625 3.823,1.781 0.24,0.156 10 false +B 4.729,1.354 5.073,1.51 0.344,0.156 10 false E2G 4.802,0.854 5.073,1.01 0.271,0.156 10 false VG 6.031,1.354 6.375,1.51 0.344,0.156 10 false EVG 6.031,0.854 6.375,1.01 0.344,0.156 10 false VG 5.667,0.958 6,1.115 0.333,0.156 10 false C39 5.677,1.458 6.01,1.615 0.333,0.156 10 false C39

for LHD
A225114E04
3.271,4.135 4.156,4.354 0.885,0.219 10 false MAIN 6.323,6.073 6.698,6.229 0.375,0.156 10 false ECM 1.115,3.396 2,3.615 0.885,0.219 10 false EFI MAIN 0.646,4.552 1.354,4.719 0.708,0.167 10 false FL MAIN 0.802,5.313 1.396,5.531 0.594,0.219 10 false Battery 3.906,3.906 4.052,4.073 0.146,0.167 10 false 1 2.948,3.906 3.094,4.073 0.146,0.167 10 false 2 3.906,3.344 4.052,3.51 0.146,0.167 10 false 3 2.948,3.344 3.094,3.51 0.146,0.167 10 false 5 5.729,3.625 5.927,3.792 0.198,0.167 10 false 44 5.708,3.802 6.01,3.99 0.302,0.188 10 false I84 5.729,4.156 5.927,4.323 0.198,0.167 10 false 81 5.677,4.344 5.99,4.531 0.313,0.188 10 false C39 6.042,4.344 6.479,4.51 0.438,0.167 10 false E1 6.042,3.792 6.479,3.948 0.438,0.156 10 false MREL 3.698,2.042 5.021,2.188 1.323,0.146 10 false Mass Air Flow Meter 3.698,1.906 4.01,2.063 0.313,0.156 10 false C41 3.396,1.625 3.552,1.781 0.156,0.156 10 false 1 5.135,1.552 5.292,1.708 0.156,0.156 10 false 2 5.135,1.052 5.292,1.208 0.156,0.156 10 false 3 5.677,1.25 5.948,1.406 0.271,0.156 10 false 118 5.729,0.76 5.938,0.917 0.208,0.156 10 false 72 3.583,1.625 3.823,1.781 0.24,0.156 10 false +B 4.729,1.354 5.073,1.51 0.344,0.156 10 false E2G 4.802,0.854 5.073,1.01 0.271,0.156 10 false VG 6.031,1.354 6.375,1.51 0.344,0.156 10 false EVG 6.031,0.854 6.375,1.01 0.344,0.156 10 false VG 5.667,0.958 6,1.115 0.333,0.156 10 false C39 5.677,1.458 6.01,1.615 0.333,0.156 10 false C39

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MASS AIR FLOW RATE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 61 319

d.

Read the value.

Result:
Result Proceed to
0.0 A
174.0 or more B
Between 1 and 173.0* C


HINT:

*: The value should change when the throttle valve is opened or closed.




A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

C

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A148358C03
1.5,0.906 1.958,1.177 0.458,0.271 1.344,2.042 0.927,2.49 true 0.104,0.104 0.302,0.281 0.198,0.177 10 false *a 0.813,2.51 1.063,2.698 0.25,0.188 10 false +B 1.594,0.979 1.917,1.156 0.323,0.177 10 false C41
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C41-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - MAIN RELAY)
3.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.
A311459C05
1.552,0.229 1.938,0.458 0.385,0.229 1.323,2.313 1.74,2.563 0.417,0.25 0.781,4.146 1.208,3.656 true 1.875,4.135 1.208,3.479 true 1.063,1.76 1.5,1.208 true 2.198,1.781 1.792,1.208 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.177,2.146 0.49,2.344 0.313,0.198 10 false *b 1.615,0.271 1.927,0.469 0.313,0.198 10 false C41 1.406,2.375 1.719,2.573 0.313,0.198 10 false C39 0.448,4.177 1.156,4.375 0.708,0.198 10 false 118 (EVG) 1.688,4.177 2.26,4.385 0.573,0.208 10 false 72 (VG) 2.125,1.802 2.406,1.979 0.281,0.177 10 false VG 0.938,1.792 1.302,1.969 0.365,0.177 10 false E2G
*a Front view of wire harness connector
(to Mass Air Flow Meter)
*b Front view of wire harness connector
(to ECM)


Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C41-3 (VG) - C39-72 (VG) Always Below 1 Ω
C41-2 (E2G) - C39-118 (EVG) Always Below 1 Ω
C41-3 (VG) or C39-72 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - MAIN RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the MAIN relay from the engine room R/B assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C41-1 (+B) - MAIN relay terminal 3 Always Below 1 Ω
C41-1 (+B) or MAIN relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.
A148358C04
1.5,0.99 1.958,1.24 0.458,0.25 1.51,2.073 1.073,2.563 true 0.094,0.094 0.354,0.302 0.26,0.208 10 false *a 0.917,2.583 1.333,2.771 0.417,0.188 10 false E2G 1.594,1.052 1.875,1.208 0.281,0.156 10 false C41
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
C41-2 (E2G) - Body ground Ignition switch ON Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.
A311459C06
1.542,0.208 1.958,0.469 0.417,0.26 1.333,2.323 1.75,2.573 0.417,0.25 0.781,4.146 1.208,3.656 true 1.875,4.135 1.208,3.479 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.177,2.146 0.49,2.344 0.313,0.198 10 false *b 1.615,0.271 1.927,0.469 0.313,0.198 10 false C41 1.417,2.375 1.729,2.573 0.313,0.198 10 false C39 0.448,4.177 1.156,4.375 0.708,0.198 10 false 118 (EVG) 1.688,4.177 2.26,4.385 0.573,0.208 10 false 72 (VG)
*a Front view of wire harness connector
(to Mass Air Flow Meter)
*b Front view of wire harness connector
(to ECM)


Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C41-3 (VG) - C39-72 (VG) Always Below 1 Ω
C41-2 (E2G) - C39-118 (EVG) Always Below 1 Ω
C41-3 (VG) or C39-72 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR